Caley Coaches CL02/2a Building Instructions Download Page 1

Caley Coaches  

 

CL02/2a Building Instructions

Page 1

0141 772 5537   

 

 

 

 

 

 

 

 Jim Smellie,

15 Tay Crescent,

Bishopbriggs,

Glasgow, G64 1EU.

CL02/2a Caledonian Railway 

Classes 812 & 652 0-6-0 

locomotives

C.R. numbers 282-293,325-328, 652-659, 661-665, 812-878 

L.M.S. numbers 17550-17645

B

UILDING

 I

NSTRUCTIONS

Parts required to complete

Motor 

Mashima 1220 “flat can” or similar recommended.

Gearbox  

High Level Loadhauler recommended. 

 

[High Level Kits, 14 Tudor Road, Chester-le_street, Co. 

 

Durham, DH3 3RY. 

 

www.highlevelkits.co.uk

]

Wheels  

5'0" diameter, 16 spoke driving wheels and

 

 

4'0" diameter, 12 spoke tender wheels

Paint and transfers.

Couplings.

Section 1  Parts list

Please check the contents of your kit and inform me of any shortages. If for any 

reason you wish to purchase parts separately, I can give you a quote for any part 

unless it is on an etched fret. Normally complete frets only are available.

Please also read the General Instructions supplied if you are not familial with 

etched kit constuction in general and 

Caley Coaches 

productions in particular.

The supplied parts, together with these instructions, assume that you are building 

Summary of Contents for CL02/2a













Reviews: