background image

Page 3

IMPORTANT SAFETY INSTRUCTIONS

WARNING

When using electrical appliances, basic safety precautions to reduce the

risk of fire, electric shock, or injury to persons should be followed, including:

1.  READ ALL INSTRUCTIONS BEFORE USING THIS WATER HEATER.

2.  This water heater must be grounded.  Connect only to properly

grounded outlet.  See “GROUNDING INSTRUCTIONS” found on page 15.

3.  Install or locate this water heater only in accordance with the provided

installation instructions.

4.  Use this water heater only for its intended use as described in this

manual.

5.  Do not use an extension cord set with this water heater.  If no receptacle

is available adjacent to the water heater, contact a qualified electrician

to have one properly installed.

6.  As with any appliance, close supervision is necessary when used by

children.

7.  Do not operate this water heater if it has a damaged cord or plug, if it is

not working properly, or if it has been damaged or dropped.

8.  This water heater should be serviced only by qualified service

personnel.  Contact nearest authorized service facility for examination,

repair, or adjustment.

SAVE THESE INSTRUCTIONS

!

Summary of Contents for NAS200 Series

























Reviews: