7.4 Programming the IMX processor
Apply power to the LMU-5541
™
, then view the terminal emulation screen.
Enter <B> to break the u-boot.
Net: FEC [PRIME]
Normal Boot
Hit 'B' to stop autoboot: 0
LMU5530-Boot >
The command prompt
“LMU-5541-Boot >”
will appear.
Type:
nand erase.chip
<enter>
LMU-5541 Hardware & Installation Guide
36/49
LMU5530-Boot > nand erase.chip
When completed,
“LMU5530-Boot >”
will appear.
NAND erase.chip: device 0 whole chip
Erasing at 0x1ffe0000 -- 100% complete.
OK
LMU5530-Boot >
7.5 USB driver installation
If the USB driver has been previously installed, skip the USB driver installation.
Power cycle the unit.
If the USB driver has never been installed, a pop-up window will appear → Driver Software Installation. Proceed with the driver install.
Upon completion, it will indicate USB Input Device Installed.
7.6 Firmware update
Remove power from the LMU-5541
™
Remove the top cover of the LMU-5541
™
Connect the 4-pin connector of 5C940 into the 4-pin header located on the board at J25. The red stripe of 5C940 is placed facing towards the
closest edge of the board.
Connect the 5-pin connector of the serial adaptor cable 5C940 to the 5-pin connector of the serial cable 134364-SER.
Connect the DB-9 connector of 134364-SER to the serial port or serial adaptor connected to the maintenance computer.
Power up the LMU-5541
™
Launch the TFTP32 or TFTP64 server.
For the Current Directory window, Browse for Directory
C:\tftpboot
For the Server interface window, select
192.168.1.189
LMU-5541 Hardware & Installation Guide
37/49
On the maintenance computer, open the command prompt by searching for
CMD.EXE
followed by <enter>
Type:
cd c:\tftpboot
At the prompt c:\tftpboot, type:
dir
<enter> (to see and verify the files)
At the prompt c:\tftpboot, type:
sb_loader.exe -f u-boot-lmu5530-btstrp.imx
<enter>
In the command prompt screen, wait for an indication of a successful download.
Looking at the Terminal Emulation screen, you will see up to 9 files being serially loaded. Wait until all the files have been loaded as it takes
several minutes. After all files are loaded “U-boot Upgrade complete” will appear
on the terminal emulation screen.
LMU-5541 Hardware & Installation Guide
38/49
7.7 Programming the co-processor
WinSCP will be used to transfer the firmware for the co-processor into the Linux system after it is running.
Launch WinSCP
Select File Protocol:
SCP
Enter Host Name:
192.168.1.55
Enter Port Number:
2001
Enter Username:
root
Enter Password:
wireless3g
Click on Login
A new WinSCP screen will appear. On the left side, browse for C:\tftpboot
The right half should be pointed to the /root directory in the LMU-5541.
LMU-5541 Hardware & Installation Guide
39/49
Transfer the file called LMU7030-CoProc_vX.X.bin via SCP over to root. Drag the file LMU7030-vX.X.bin across the screen to the root side.
On the Terminal Emulation screen, press <Enter> to bring up the LMU5530 login:
Username:
root
Password:
wireless3g
Type:
ls
<Enter> (to view the name of the bin file)
Type:
lmu5530_program_stm8.sh /root/<file_name.bin>
<Enter>
Note:
the bin file name is case sensitive and must be entered exactly as shown.
The co-processor, STM8, is being programmed.
LMU-5541 Hardware & Installation Guide
40/49
Programming is complete when “success” is returned and the
“root@LMU5530:~#”
prompt is displayed.
To view co-processor info type:
stm_cli --info
7.8 Final Steps
