CAL Controls CALCOMMS 3300, Communications Manual

Page: 6 / 25

COMMERCIAL IN CONFIDENCE
Page 5
1.3 Level C - parameters in address order
Parameter
Name Size Address
(hex) R/W ModBus
Function
read/write Internal Storage, Step rate in
Internal units Comments
Addr 1 03D5 RW 3/6 0..255 valid range 1..247
Baud 1 03D6 RW 3/6 0=1200, 1=2400, 2=4800, 3=9600,
4=19200
Data 1 03D7 RW 3/6 0=18n1, 2=18e1, 3=18o1,
Dbg 1 03D8 RW 3/6 0=off, 1=on
note that all changes to the communications level parameters take effect immediately on leaving the
menu, or on receipt of the
exit program mode command. The dbg feature may be set on or off. When
on, the right-most digit will flash 3 horizontal segments on receipt of a character when a
communications board is fitted, the left-most digit will flash on transmission of a character.
1.4 Level 1 - parameters in address order
Parameter
Name Size Address
(hex) R/W ModBus
Function
read/write Internal Storage, Step rate in Internal units,
Limits Comments
Set.2 2 0081 RW 3/6 Degrees * 10 [LIN]
Step 0.1 or 1 depending on disp selection
min=LoSc, max=HiSc
Ofst 2 0083 RW 3/6 Degrees * 10 [LIN]
normal inc/dec
see separate details for limits
Band 2 0085 RW 3/6 Degrees * 10 [LIN]
normal inc/dec
min=0.1 max=25% of Sensor Maximum
9500 max is
100% of sensor
maximum
Bnd.2 2 0087 RW 3/6 Degrees * 10 [LIN]
normal inc/dec
see separate details for limits
Tune 1 0189 RW 3/6 0=off, 1=on, 2=park, 3=at Setpoint
Dac 1 018A RW 3/6 stored as value*2 so 0.5 is stored as 1
step by 0.5
Min=0.5 max=5.0
Int.t 1 018B RW 3/6 intt * 10 up 10.0, then intt+90
normal inc/dec
0=off min=0.1, max=60
Der.t 1 018C RW 3/6 1 — 200 in 1 sec steps
Cyc.t 1 018D RW 3/6 Cyct * 10 up 10.0, then Cyct+90
normal inc/dec
0=off min=0.1, max=81
Cyc.2 1 018E RW 3/6 Cyc2 * 10 up 10.0, then Cyc2+90
normal inc/dec
0=off min=0.1, max=81
SP.lk bit 0028 RW 1/5 0=off, 1=on
SPrr 2 02D0 RW 3/6 Stored as SPrr
if <100 step by 1, if <1000 step by 5 else step by
10
min=0 max=9990
9500 display
effected by DECP
when LIN input
selected
Soak 2 02D2 RW 3/6 0xFF00 = - - , 0=off, otherwise Soak * 10
Step by 1 up to 120, then 5 up to 300 then by 10
min = 1, max=1440
SPrn 1 03D4 RW 3/6 0=off, 1=on, 2=hold 9500P See Level P
section for notes
on starting a
program