CAL Controls CAL 9500P, Abridged User Manual

Page: 8 / 24

8
INPUT SELECTION AND RANGING
dI.SP [1] 0.1
Select display resolution: for display of process value, setpoint,
OFSt, Set.2, hi.SC, LoSC
.
hi.SC
[sensor maximum] sensor maximum
°C/°F/units
Set full scale
Lo.SC
[sensor minimum] sensor minimum
°C/ºF/units
Set scale minimum (default 0°C/32°F or 0 units)
inPt
Select input sensor
[nonE]
(See SENSOR SELECTION table, page 22)
NB. If Linear Input selected, start configuration from Level A .
unit [nonE] °C °F bAr Psi Ph rh SEt
Select required operating unit from above options
LEVEL 3
OUTPUT CONFIGURATION
Note 1 : ‘ Read only’ after initial configuration.
rSET ALL
full reset to factory settings
required to change
SP1.d
subsequently.
Note 2 : Depending on the Model, SP1 and SP2 may be fitted with any of three output
types, RLY , SSd or Analogue (Specification on page 11/12) where appropriate,
these must be allocated during initial configuration. SP3 is always fitted with RLY .
Output Options Table
Model SP1 Output SP2 Output SP3 Output
95111P RLY RLY RLY
95001P SSd RLY RLY
RLY SSd RLY
95221P SSd SSd RL Y
*95X11P AnLG RLY RLY
RLY AnLG RLY
*95X21P AnLG SSd RLY
SSd AnLG RLY
* Substitute for X in table above, Analogue options B = 4–20mA, C = 0–5V, D = 0–10V
Will be affected by dECP settings in Level A
✢
✢
✢
Re-transmission
* These models above offer the option of using the analogue output for Re-transmission .
Select
bAnd
or
bnd.2
value in
LEVL 1
to equal the full range setting in
LEVL A
and if
using SP1 output, set
int.t
and
dErt.t
in
LEVL 1
to off.
Example: Set-Up using a Model 95B11P to Re-transmit the 4-20 mA input, scaled 0 to 100
units. SP1 relay is used as the control output and SP2 analogue output is used for re-
transmission.
Note : Read in conjunction with Linear Input Set-up Procedure on page 6.
Function Options
[Factory settings] shown in brackets
From initial power-up;
Set
inPt nonE
to
inPt Lin
unit nonE
to
unit SEt
(for example)
SP1.d nonE
to
SP1.d rLY
To scale the input, select
LEVL A
, then:
Set
dECP
to
000.0
(e.g. required resolution)
An.hi
to
100.0
An.Lo
to
0.0
hi.in
to
50
(ie 20mA)
Lo.in
to
10
(ie 4mA)
To align SP2 analogue re-transmission with SP1 control output, select LEVL 2 then:
Set
SP2.A
to
FS.hi
And in LEVL.1
Set
SEt.2
to
50
(ie 50% of display range)
bnd.2
to
100
(ie 100% of display range)
Finally, set SP1 setpoint value as required for process to start.
Using SP1 output for re-transmission
Set
int.t
to off
dErt
to off
rev.d
to
1d.2d
to invert SP1 output
SP1 Setpoint to midscale
burn
Sensor burn-out/break protection
Caution: Settings affect fail safe state.
SP1 SP2
[uP.SC]
Upscale Upscale
dn.SC
Downscale Downscale
1u.2d
Upscale Downscale
1d.2u
Downscale Upscale
Retransmission range is limited to the sensor full scale value (Example RTD = 400C/752F).
LEVL 3
LEVEL 2 CONTINUED
English