background image

COMMERCIAL IN CONFIDENCE

Page 18

2. Write the Setpoint value

The setpoint value must be sent in the same units as are currently displaying on the controller, that is,
in Degrees Fahrenheit, if selected, otherwise in Centigrade. The value to be transmitted must be an
integer number of 10ths of a degree. For example, to transmit a value of 432.1 degrees, the setpoint
register must be set to 4321 (decimal) which is 10E1 (hex). The following message writes the setpoint,
in this example xx would be 10 (hex) and yy  would be E1 (hex).

byte 0

Slave address

xx

byte 1

Function code

(write register)

06 hex (always)

byte 2

:

Register Address high byte

00 hex (always)

byte 3

:

Register Address low byte

7F hex (always)

byte 4

:

Setpoint Value high byte

xx

byte 5

:

Setpoint Value low byte

yy

byte 6

:

CRC low byte

??

byte 7

:

CRC high byte

??

3. Exit program mode

A two part sequence, similar to the 

enter program mode

 sequence is required to accept the new values

and unlock the controller keypad. Similarly, both messages must be present in strict sequence for the
values to take effect.

            1st Message:

byte 0

Slave address

xx

byte 1

Function code

(write register)

06 hex (always)

byte 2

:

Register Address high byte

03 hex (always)

byte 3

:

Register Address low byte

00 hex (always)

byte 4

:

Register Value high byte

00 hex (always)

byte 5

:

Register Value low byte

06 hex (always)

byte 6

:

CRC low byte

??

byte 7

:

CRC high byte

??

The controller should reply with an identical response, if not, this message should be re-
transmitted until the response is correct.

Note: the 9500 does not require the security message to be sent.

2nd Message:

byte 0

Slave address

xx

byte 1

Function code

(write register)

06 hex (always)

byte 2

:

Register Address high byte

16 hex (always)

byte 3

:

Register Address low byte

00 hex (always)

byte 4

:

Register Value high byte

00 hex (always)

byte 5

:

Register Value low byte

00 hex (always)

byte 6

:

CRC low byte

??

byte 7

:

CRC high byte

??

The CAL Controller should reply with an identical response, if not, the message pair is lost and
the 

exit program mode 

sequence must be repeated from message 1.

Any changes made will only take effect on receipt a valid 

exit program mode 

sequence - if the

controller is de-powered before this sequence is completed, the previously stored values will be used.

Summary of Contents for 3300P


























Reviews: