Hub Hinge Uprights are easily adjusted vertically at all attachment points to accommodate variations in
limb lengths.
To adjust, loosen the Phillips screw slightly and slide upright up or
down along channel to desired position.
(Figure 17)
Re-tighten. Repeat on opposite side, ensuring both sides are
equal in position and length.
Adjust Range of Motion (ROM)
The Hub Hinges offer full and incremental ROM adjustment in
varying degrees, including complete lock-out in any position. To
adjust ROM, loosen and remove the Phillips screws located in
the Hub.
(Figure 18)
Determine desired ROM. Re insert screws to provide the
intended protected ROM.
(Figure 19)
If full ROM is desired, the set screws may be removed entirely.
(Figure 20)
To set in lockout or full extension, position the hinge at the desired angle.
Insert screws at points closest to the pivot to prevent the hinge from
moving from this position.
(Figure 21)
Achilles Brace System Application
To apply, fully open both sections of the brace, by
releasing the Boa Reels and lifting the Hook Tabs
away from the Loop material on the clamshell.
(Figure 22)
If length adjustment is required, loosen the Hub Hinge
Upright screws.
(Figure 23)
Apply the opened clamshell sections of the brace to the
posterior aspect of the limb. The Caerus logo faces BACK.
(Figure 24)
Align each section to the desired location, paying particular attention that
the Hub Hinge pivots are aligned with the tarsal joint axis. If loosened re-
tighten the Phillips dome head screws.
(Figure 25)
Close the brace, by placing the front (cranial) shells to fit within the
back (caudal) clamshells. Re-apply the Hook Tabs to their
respective Loop areas on the clamshells. Close each section of the
brace, by tightening the Boa reels, working from lower (distal) to
upper (proximal) sections.
(Figure 26)
NOTE:
Since the Cranial clamshells are completely detachable,
specific length adjustments, upward or downward, are available to
further provide an optimal fit.
Adjust the ROM as condition indicates.
Spot Heating
The brace may be spot molded to provide a better fit and
eliminate areas of irritation.
(Figure 27)
Use a hair dryer on medium heat and high speed to heat the
area. Keep the heat source four to six inches away from the
brace. The material will soften in approximately two minutes.
Be careful not to overheat.
The Caerus Slim Line Heater may also be used, as described
earlier. See Figure 1.
(Figure 28)
Once pliable, bend the material to the desired position and hold
until the material hardens. Reapply the brace.
T
he brace may be
reheated and remolded as needed.
The Brace thermoplastic and foam may also be trimmed to fit
uneven contours.
Care and Cleaning
If brace and/or padding becomes wet or soiled, remove the foam padding to hand wash with mild soap
and air dry. Padding may be replaced with Caerus Replacement Padding. Exposing brace to
temperatures over 130°F may cause the brace to lose its shape.
Check Screws Weekly
At least weekly, check and if necessary, re-tighten the Phillips
screws on both the Hub Hinge and Uprights.
(Figure 29)
Protocol and Wearing Recommendations
The following recommendations are general guidelines only. Each protocol should be tailored to the
individual needs of the patient and be based on injury severity and healing progress. The patient should
be closely monitored for healing progress, advancements in mobility and weight bearing, as well as brace
fit and adjustment needs during the healing process. Protocols should be reevaluated and modified as
needed by veterinary care provider.
Post-Op
For use in the event of surgery, the brace should be worn for 24/7 during the first 4 to 8 weeks, unless
otherwise recommended. If the surgery site has stabilized, the brace may be removed for short periods
of time, approximately 1
to 2 hours, only while the dog is under full supervision and full control to prevent re-injury. After the 8th
week the brace should be worn during times of activity to prevent re-injury and may be worn for an
additional 2 to 3 months or as needed.
Conservative Care
For use in the event of acute ligament tear or to prevent re-injury. The brace should be worn 24/7 until
the dog will bear normal weight on the injured leg. Longer term stabilization may be required, and the
brace should be used during times of activity to prevent re-injury or 24/7 if necessary.
Dog Types, Weight Ranges and Tibia Measurement Ranges
• Extra Small fits 10 to 25 lbs., suc
h as Shiatsu and Pug -
2.75”
-
4.0”
• Small fits 25 to 40 lbs., such as Whippet
and Shetland Sheepdog -
3.75”
-
5.5”
• Medium –
40 to 65 lbs. - Boxer, Bull Dog, Cocker Spaniel, Australian Sheppard, Greyhound
–
5.0”
-
7.0”
• Large –
65 to 90 lbs. - Labrador, German Sheppard, Doberman, Husky, Border Collie
–
6.0”
-
8.0”
• Extra Large –
90+ lbs. - Great Dane, St. Bernard, Weirmaraner, Bernese Mountain Dog
–
7.0”
-
11.0”
US and International Patents Pending
Manufactured by
Caerus Corp
1251 Red Fox Road
Arden Hills, MN 55112
651-440-9345
www.caeruscorp.com
© 2016 Caerus Corp
IFU ABS 12 2016
