background image

 

Visit the Lepton

7

 R7100C web page, you will find the latest revision 

of data sheets, manuals, certifications, technical drawings, software and firmware. 

All you need to start using your reader in a few clicks! 

Scope of Manual 

The goal of this manual is to provide the basic information to work with the Lepton

7

 R7100C Reader. 

Change Document Record 

Date 

Revision 

Changes 

Pages 

07/04/2022 

Preliminary revision 

19/05/2022 

0.1 

Added  Federal  Communications  Commission  (FCC)  Notice 
(Preliminary) 

Added 

FCC Compliance

 paragraph in the Regulatory Compliance 

chapter 

21,22 

30/06/2022 

0.2 

Corrected minimum separation distance requirement 

21,22 

Reference Document 

[RD1]

 

EPCglobal:  EPC  Radio-Frequency  Identity  Protocols  Class-1  Generation-2  UHF  RFID  Protocol  for 
Communications at 860 MHz – 960 MHz, Version 2.0.1 (April 2015).  

 

 

 

CAEN RFID srl 

Via Vetraia, 11 55049 Viareggio (LU) - ITALY 
Tel. +39.0584.388.398 Fax +39.0584.388.959 

[email protected] 
www.caenrfid.com 

 
 

 

 

© CAEN RFID srl – 2022 

Disclaimer 

No part of this manual may be reproduced in any form or by any means, electronic, mechanical, recording, or 
otherwise, without the prior written permission of CAEN RFID. 

The  information  contained  herein  has  been  carefully  checked  and  is  believed  to  be  accurate;  however,  no 
responsibility  is  assumed  for  inaccuracies.  CAEN  RFID  reserves  the  right  to  modify  its  products  specifications 
without giving any notice; for up to date information please visit 

www.caenrfid.com

 

 

 

Preliminary Product Information

 

This  document  contains  information  for  a  new  product.  CAEN  RFID  reserves  the  right  to  modify  this  product 
without notice. 

“Preliminary”  product  information  describes  products  that  are  ready  for  production,  but  for  which  full 
characterization data is not yet available. CAEN RFID believes that the information contained in this document is 
accurate  and  reliable.  However,  the  information  is  subject  to  change  without  notice  and  is  provided  “AS  IS” 
without  warranty  of  any  kind  (Express  or  implied).  You  are  advised  to  obtain  the  latest  version  of  relevant 
information to verify, before placing orders, that information being relied on is current and complete. All products 
are  sold  subject  to  the  terms and  conditions  of sale  supplied  at  the time  of  order  acknowledgement,  including 
those pertaining to warranty, patent infringement, and limitation of liability.  No responsibility is assumed by CAEN 
RFID for the use of this information, including use of this information as the basis for manufacture or sale of any 
items, or for infringement of patents or other rights of third parties. 

Summary of Contents for Lepton7 R7100C























Reviews: