background image

FAST-PS-1K5 – User’s Manual 

 

 

The  WARNING sign denotes a hazard. An attention 

to a procedure is  called.  Not following the procedure correctly could  result 
in  personal  injury.  A  WARNING  sign  should  not  be  skipped  and  all 
indicated conditions must be fully understood and met. 

 

 

 The CAUTION sign denotes a hazard. An attention to 

a  procedure  is  called.  Not  following  procedure  correctly  could  result  in 
damage to the equipment. Do not proceed beyond a CAUTION sign until all 
indicated conditions are fully understood and met. 

 
 

CAEN  ELS  S.r.l.  will  repair  or  replace  any  product  within  the  guarantee 

period if the Guarantor declares that the product is defective due to workmanship or 
materials and has not been caused by mishandling, negligence on behalf of the User, 
accident or any abnormal conditions or operations. 
 

Please read carefully the manual before operating any part of the instrument 

 

 
 

 

Do NOT open the BOX TOP 

COVER

 

 

 

 
 
 

 

CAEN ELS S.r.l. declines all responsibility for damages or injuries caused 

by an improper use of the Modules due to negligence on behalf of the User. It is 
strongly recommended to read thoroughly this User's Manual before any kind of 
operation.  
 
 

CAEN ELS S.r.l. reserves the right to change partially or entirely the contents of this 

Manual at any time and without giving any notice. 

 

 
 
 
 
 
 
 

WARNING 

CAUTION 

WARNING 

Summary of Contents for FAST-PS-1K5 100-15



















































Reviews: