Cadillac Escalade 2020 Owner'S Manual Download Page 76 | Manualshive

Page: 76 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

76

SEATS AND RESTRAINTS

If the vehicle has rollover roof-rail
airbags, see

Different Size Tires and

for additional important

information.

If the vehicle must be modified
because you have a disability and have
questions about whether the
modifications will affect the vehicle's
airbag system, or if you have
questions about whether the airbag
system will be affected if the vehicle is
modified for any other reason, see
your dealer.

Airbag System Check

The airbag system does not need
regularly scheduled maintenance or
replacement. Make sure the airbag
readiness light is working. See

Readiness Light

.

Caution

If an airbag covering is damaged,
opened, or broken, the airbag may
not work properly. Do not open or
break the airbag coverings. If there

(Continued)

Caution (Continued)

are any opened or broken airbag
coverings, have the airbag covering
and/or airbag module replaced. For
the location of the airbags, see

Where Are the Airbags?

. See

your dealer for service.

Replacing Airbag System
Parts after a Crash

{

Warning

A crash can damage the airbag
systems in the vehicle. A damaged
airbag system may not properly
protect you and your passenger(s)
in a crash, resulting in serious
injury or even death. To help make
sure the airbag systems are working
properly after a crash, have them
inspected and any necessary
replacements made as soon as
possible.

If an airbag inflates, you will need to
replace airbag system parts. See your
dealer for service.

If the airbag readiness light stays on
after the vehicle is started or comes
on when you are driving, the airbag
system may not work properly. Have
the vehicle serviced right away. See

Airbag Readiness Light

.

«
...
74
75
76
77
78
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Raven Pages: 24

Brand: Weather Guard Pages: 4

Brand: Trailboss Pages: 5

Brand: Thule Pages: 12

Brand: tams elektronik Pages: 44

Brand: Ford Pages: 8

Brand: Intec Pages: 16

Brand: H&S Pages: 32

Brand: Saab Pages: 92

Brand: A-rival Pages: 23

Brand: SilverLeaf Electronics Pages: 16

Brand: Mercedes-Benz Pages: 91

Brand: Honda Pages: 124

Speed & Route Profiler

Brand: Racelogic Pages: 24

Brand: Calix group Pages: 4

Portable Car Umbrella

Brand: Mynew Pages: 5

Brand: TATA Motors Pages: 151

QUICKDRAW RACHET TIE-DOWNS 855

Brand: Thule Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands