manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

DRIVING AND OPERATING

247

Turn Signals When Towing a
Trailer

When properly connected, the trailer
turn signals should will illuminate to
indicate the vehicle is turning,
changing lanes, or stopping. When
towing a trailer, the arrows on the
instrument cluster will illuminate
even if the trailer is not properly
connected or the bulbs are
burned out.

Tow/Haul Mode

For instructions on how to enter Tow/
Haul mode, see

Tow/Haul Mode

0

194

.

Tow/Haul assists when pulling a
heavy trailer or a large or heavy load.

Tow/Haul Mode is designed to be
most effective when the vehicle and
trailer combined weight is at least
75% of the vehicle's Gross Combined
Weight Rating (GCWR). See

“

Maximum Trailer Weight

”

under

Trailer Towing

0

240

.

Tow/Haul Mode is most useful when
towing a heavy trailer or carrying a
large or heavy load:

.

through rolling terrain

.

in stop-and-go traffic

.

in busy parking lots

Operating the vehicle in Tow/Haul
Mode when lightly loaded or not
towing will not cause damage;
however, it is not recommended and
may result in unpleasant engine and
transmission driving characteristics
and reduced fuel economy.

Trailer Sway Control (TSC)

Vehicles with StabiliTrak have a
Trailer Sway Control (TSC) feature.
Trailer sway is unintended side-to-side
motion of a trailer while towing. If the
vehicle is towing a trailer and the TSC
detects that sway is increasing, the
vehicle brakes are selectively applied
at each wheel, to help reduce
excessive trailer sway. If equipped with
the Integrated Trailer Brake Control
(ITBC) system, and the trailer has an
electric brake system, StabiliTrak may
also apply the trailer brakes.

If TSC is enabled, the Traction Control
System (TCS)/StabiliTrak warning
light will flash on the instrument
cluster. Reduce vehicle speed by
gradually removing your foot from the
accelerator. If trailer sway continues,
StabiliTrak can reduce engine torque
to help slow the vehicle. TSC will not
function if StabiliTrak is turned off.
See

Traction Control/Electronic Stability

Control

0

201

.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Kargo Master 40131 Installation Manual preview
40131
Brand: Kargo Master Pages: 5
Bestop WrapAround Windjammer Installation Instructions Manual preview
WrapAround Windjammer
Brand: Bestop Pages: 7
Lexus LX 470 Owner'S Manual preview
LX 470
Brand: Lexus Pages: 369
Mountain Top Sports Bar Installation Manual preview
Sports Bar
Brand: Mountain Top Pages: 12
Veigel S47290920 Installation And Operating Instructions Manual preview
S47290920
Brand: Veigel Pages: 24
Cellular Line interphone Instruction Manual preview
interphone
Brand: Cellular Line Pages: 25
Metra Electronics 99-7477 Installation Instructions preview
99-7477
Brand: Metra Electronics Pages: 2
Buick 2015 LaCrosse Getting To Know Manual preview
2015 LaCrosse
Brand: Buick Pages: 20
Columbia THERAPEDIC 2000 Instructions For Use Manual preview
THERAPEDIC 2000
Brand: Columbia Pages: 14
Jeep CHEROKEE 2017 User Manual preview
CHEROKEE 2017
Brand: Jeep Pages: 374
Volvo 30795637 User Manual preview
30795637
Brand: Volvo Pages: 92
Reliant ROBIN 850 Workshop Manual preview
ROBIN 850
Brand: Reliant Pages: 206
Whispbar K481W Fitting Instructions Manual preview
K481W
Brand: Whispbar Pages: 14
PMT AS7.M100.001 User Manual preview
AS7.M100.001
Brand: PMT Pages: 16
Discount Car Stereo A2DIY-JAG98 Quick Start Manual preview
A2DIY-JAG98
Brand: Discount Car Stereo Pages: 11
Vmac A700308 Installation Manual preview
A700308
Brand: Vmac Pages: 16
Yakima TopWater Quick Start Manual preview
TopWater
Brand: Yakima Pages: 9
STO N SHO SNS 297 Installation Procedures Manual preview
SNS 297
Brand: STO N SHO Pages: 7

Brands by name

Popular brands

Load more brands