Maintenance:
For more effective and safer operation and to prolong
the life of the heater, read the Owner’s Guide and follow the
maintenance instructions included with each heater. Failure to
properly maintain the heater will void any warranty and may cause
the heater to function improperly. Warranties are non transferable and
apply to original consumer only. Warranty terms are set out below.
LIMITED ONE-YEAR WARRANTY:
Cadet will repair or replace any
Cadet product, including thermostats, found to be defective within one
year after the date of purchase.
Extended Product Warranty
LIMITED TWO-YEAR WARRANTY:
Cadet will repair or replace any
NLW Series element or motor found to be defective within two years
after the date of purchase.
THESE WARRANTIES DO NOT APPLY:
1. Damage occurs to the product through improper installation or
incorrect supply voltage;
2. Damage occurs to the product through improper maintenance,
misuse, abuse, accident, or alteration;
3. The product is serviced by anyone other than Cadet.
4. If the date of manufacture of the product cannot be determined;
5. If the product is damaged during shipping through no fault of Cadet.
6. CADET’S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT
AS SET OUT HEREIN. CADET SHALL NOT BE LIABLE FOR
DAMAGES
SUCH
AS
PROPERTY
DAMAGE
OR
FOR
CONSEQUENTIAL DAMAGES AND/OR INCIDENTAL EXPENSES
RESULTING FROM BREACH OF THESE WRITTEN WARRANTIES
OR ANY EXPRESS OR IMPLIED WARRANTY.
7. IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR
CADET PRODUCT, THE REPLACEMENT PARTS ARE SUBJECT TO
THE SAME WARRANTIES AS THE PRODUCT. THE INSTALLATION
OF REPLACEMENT PARTS DOES NOT MODIFY OR EXTEND
THE UNDERLYING WARRANTIES. REPLACEMENT OR REPAIR
OF ANY CADET PRODUCT OR PART DOES NOT CREATE ANY
NEW WARRANTIES.
8. These warranties give you specific legal rights, and you may also
have other rights which vary from state to state. Cadet neither
assumes, nor authorizes anyone to assume for it, any other
obligation or liability in connection with its products other than as
set out herein.
If you believe your Cadet product is defective, please, contact Cadet
Manufacturing Co. at 360-693-2505, during the warranty period, for
instructions on how to have the repair or replacement processed.
Warranty claims made after the warranty period has expired will be
denied. Products returned without authorization will be refused.
Parts and Service
Contact Cadet for information on Parts or Service.
Warranty
CONSULT LOCAL ELECTRICAL CODES TO DETERMINE WHAT WORK MUST BE PERFORMED BY QUALIFIED ELECTRICAL SERVICE PERSONNEL
Symptom
Problem
Solution
Breaker trips immediately
upon energizing heater.
Heater fan operates,
but does not discharge
warm air.
Heater will not shut off.
Heater discharges smoke
or emits a burnt odor.
Element heats for a moment
without the fan turning, then
immediately stops heating.
Heater does not run.
Troubleshooting Chart
1. Incorrect supply voltage.
2. Overloaded circuit.
3. A short circuit exists in the supply
or heater wiring.
4. Defective circuit breaker.
1. Insufficient element temperature.
2. Incorrect supply voltage.
3. Element has failed.
4. Thermostat knob is not turned
clockwise far enough to activate heater.
1. Heat loss from room is greater than
heater capacity.
2. Defective thermostat.
1. Dust, lint or other matter has
accumulated inside heater.
1. Defective motor or internal connection.
2. Fan or motor jammed.
1. Thermostat set too low.
2. Heater has tripped the high-
temperature reset switch.
3. Power not on at the circuit breaker.
4. Broken or poorly connected
wire(s) to heater.
5. Defective thermostat.
1. Verify that supply voltage matches the heater rating.
2. The total amperage of all heaters on a branch circuit must not be more
than 80% of the amperage rating of the circuit breaker and supply wire
ratings. Use a lower wattage heater, or reduce the number of heaters
on the circuit.
3. Shorted supply or heater wires may be accompanied by severe sparking.
Inspect all supply and heater wiring insulation for damage. Do not reset
the circuit breaker until all electrical shorts have been repaired.
4. Replace the circuit breaker.
1. Allow a few moments for element to reach operating temperature.
2. Verify that supply voltage matches the heater rating.
3. Replace element.
4. Turn up thermostat.
1. Close doors and windows. Provide additional insulation, install a
higher-wattage heater or multiple heaters if necessary.
2. Adjust thermostat to its lowest setting. If heater continues to run
(allow two minutes for the thermostat to respond) and room temperature
is greater than 50 degrees, replace thermostat.
1. Clean heater (see “Operation & Maintenance” section for instructions).
1. Heater or fan motor requires replacement.
2. Remove obstruction and press heater reset button (after allowing the unit
to cool). Test heater operation--if reset button has been pressed (be sure
to listen and feel for a click indicating it has been reset), but heater does
not run, heater requires repair or replacement.
1. Adjust thermostat to a higher temperature until heater operates.
2. Press the heater reset limit control (see “Operation & Maintenance”
section for instructions).
3. Turn on the correct circuit breaker in the main panel.
4. Turn off power at circuit breaker. Check supply wire continuity and
proper connection to heater wires.
5. The entire heater, or any of its components may be checked for
continuity to determine the cause of any problem. Repair or replace
the heater.
©2007 Cadet Manufacturing Co.
Printed in U.S.A. Rev. 4/07 #720117
4