3
3
6. Operating the Appliance
• Always operate the appliance on a firm level surface.
• The heater has three settings. Low, Medium, and High (Fig.3).
Lighting the appliance
• Do not attempt to light the appliance if you suspect any leaks.
• Turn the control knob of the gas cylinder to open the gas cylinder.
•
NB!
The pipe system needs to be purged of air before igniting will take place. Note
that if you have just refilled your cylinder, that purging may take a little longer due to
access air in the cylinder.
To purge press in the control knob on the OFF setting, while
holding down the control knob turn to the Low setting for about 15 seconds to allow
the gas to fill the pipe system and then press the piezo ignitor in with your thumb
while still holding in the control knob, until the pilot burner ignites. Note to hold the
control knob in for a further 2-5 seconds after the pilot burner is alite in order for the
flame failure device to heat. Then press the ignitor button to ignite the Low panel.
• If you press the ignitor before purging the pipe system, it will not light.
• Once the pilot burner is alight, it means that the heater is at minimum position. If pilot flame goes out please repeat this procedure.
Heat settings
• To change from low to minimum, gently press in the control knob about 3/4 inwards and turn the control knob anti-clockwise to
position 2. If you press the control knob in too far, it will not turn.
• To change from medium to maximum, gently press in the control knob and turn it anti-clockwise to position 3.
• Turn off the heater at the cylinder first, and then the heater control knob.
Attention!
• Please ensure you have locked the control knob while changing position. Try to turn the control knob without forcing and pushing
downward to be sure that control knob is locked. The control knob should not turn without pushing downward.
• After lighting, operate the appliance upright and do not move it around. Flaring may occur if the appliance has not fully warmed up or
if it is moved around carelessly.
• After use, ensure that the cylinder valve is closed (turn control knob fully clockwise).
• After use, allow the appliance to cool down sufficiently before touching any parts.
5. Fitting and Changing the Gas Cylinder
• Ensure that the gas cylinder is fitted or changed in a well-ventilated location, preferably outdoors, away from any source of ignition,
such as naked flames and away from other people.
• Do not smoke while changing the cylinder.
• When you need to replace your empty cylinder, turn the gas off at the valve or regulator of the cylinder and take the empty cylinder out
of the heater. Make sure that the heater is extinguished completely.
• Remove the regulator from the empty cylinder.
• Use an approved regulator and hose. This hose must be a mimimum of 500mm in length. Avoid twisting the hose whilst connecting
the regulator to the cylinder. Please seek advice from your gas and regulator supplier so as to use correct hose and regulator.
• Blow out any dust from the cylinder opening to prevent possible blockage of the jet.
• Place the full cylinder in its allocated space and attach the rear cover.
• Ensure that a complete gas seal has been made (check for the smell of gas around the connection joint). If you have to check for a gas
leak, do this outdoors. Do not check for leaks with a naked flame. Use warm soapy water only, applied to the joints and connections of
the appliance. Any leakage will show up as bubbles around the leakage area. If you are in doubt, contact your nearest stockist.
• After use, always ensure that the control knob is turned to the “off” position (turn fully clockwise).
• After use, turn off the appliance at the gas container valve.
• When changing the gas cylinder be aware that the appliance will be very hot, allow to cool or make use of oven gloves
Fig. 3
4. Assembly
• Fit the wheels to the bottom by simply screwing them on in a clockwise direction using the spanner provided.
7. Warning
•
Use an appropriate regulator which is adjusted to 2.8kPa.
•
Do not keep pressing the gas inlet valve button for more than 40 seconds.
•
Never disconnect the regulator while cylinder valve or regulator is open.
•
Do not change cylinders within areas in which open fire exists.
Summary of Contents for 942
Page 2: ......
