background image

5-2   SmartSwitch 9A100 Installation and Setup Guide

Technical Specifications

  Specifications

.

Note

The ‘MON' and ‘DIAG' functions are not used in this release.

5.2

TECHNICAL SPECIFICATIONS

Table 5-1

Front panel LEDs

LED

Function

FAIL (red)

Normally OFF; ON indicates CPU failed.

STATUS 
(amber)

Normally OFF; ON indicates an error condition that prevents alarm information from being 
displayed to the console.

POWER 
(green)

Normally ON; OFF indicates the CPU is not receiving power from the power supply.

RX DATA 
(green)

Normally FLASHING intermittently if there is receive activity on the port; indicates the Ethernet 
port is up and receiving Ethernet frames.

TX DATA 
(green)

Normally FLASHING intermittently if there is transmit activity on the port; indicates the Ethernet 
port is up and transmitting Ethernet frames.

Table 5-2

Hardware specifications

Specification

Value

Processor

i960CF, 33 MHz

Switching engine

2.5 Gbps, non-blocking

Max I/O ports

45 for 6-slot chassis; 105 for 14-slot 
chassis

Switch latency

10 microseconds

CPU DRAM memory

32 MB 

Buffer memory (cells)

32 K

flash memory

8 MB

Serial port

RS-232c compliant; RJ-45 connector

Ethernet port

IEEE 802.3 compliant; RJ-45 connector

Summary of Contents for SmartSwitch 9A100





















































Reviews: