Cabletron Systems MMAC-Plus 9T125-08 Reference Manual Download Page 31 | Manualshive

Page: 31 / 36

Cabletron Systems MMAC-Plus 9T125-08 Reference Manual Download Page 31

29

9T125-08 Module Specific Information

Token Ring LAN Statistics

The Token Ring LAN Statistics (TOTAL) Screen (Figure 9), displays the module’s
error statistics.

Figure 9. Token Ring LAN Statistics (TOTAL) Screen

SmartSwitch 9000 Local Management

Token Ring LAN Statistics (TOTAL)

Module Name: 9T125-08 Firmware Revision: 01_00_00

Slot Number: 10 BOOTPROM Revision: 01.00.05

System Up Time: 000 + 00:33:36 Ring Number: 0x002

Frames Transmitted: 512 Ring Status: Normal

Frames Received: 508 Ring Speed (Mbps): 16

KBytes Transmitted: 25 Stations on Ring: 2

KBytes Received: 25 Ports Enabled: 6

Beacon States: 0 Active Monitor Changes: 0

Ring Purges: 2 Active Monitor Address: 00-00-B8-74-40-7A

ISOLATING ERRORS NON-ISOLATING ERRORS

Line Errors: 0 Lost Frame Errors: 0

Burst Errors: 2 Frame Copied Errors: 0

AC Errors: 0 Rcvr Congestion Errors: 0

Abort Transmit Errors: 0 Token Errors: 2

Internal Errors: 0 Frequency Errors: 0

[ TOTAL ] [TOKEN RING 1] [REFRESH 3sec] EXIT RETURN

«
...
29
30
31
32
33
...
»

Summary of Contents for MMAC-Plus 9T125-08





































Reviews:

No comments