background image

 

i

Notice

 

Notice

 

Cabletron Systems reserves the right to make changes in specifications and other information 
contained in this document without prior notice. The reader should in all cases consult Cabletron 
Systems to determine whether any such changes have been made.

The hardware, firmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, 
SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED 
TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION 
CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR 
SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

© Copyright February 1998 by:

Cabletron Systems, Inc.
35 Industrial Way
Rochester, NH 03867-5005

All Rights Reserved
Printed in the United States of America

Order Number: 9032531-01

 

LANVIEW 

 

is a registered trademark and

 

 SmartSwitch 

 

is a trademark of Cabletron Systems, Inc.

 

i960 microprocessor

 

 is a registered trademark of Intel Corp.

 

Ethernet

 

 is a trademark of Xerox Corporation.

Summary of Contents for FPIM 02 FPIM-02



























Reviews: