background image

 

 

 Connections to speakers

0

 plugs

these outputs can be used to bring the signal to the main 
loudspeaker systems.
the signal from the l (left) and R (right) tO SPeAKeRS

0

 

plugs is the one being brought in by the FROM ReCeIVeR

9

 

connectors. these outputs can thus be used to bring the si-
gnal to the main loudspeaker systems.

Power supply

the AC in

-

 cord must be connected to the mains to supply 

the subwoofer. the selection of the right voltage 115 V - 230 V 
is done with 115 V - 230 V

=

. Switch POWeR

q

, on StAND 

By or ON. With the switch on the StAND By position, the 
unit will mute after a few minutes without input signal. the 
system turns on automatically when signal comes back.

Adjustments

 

 VoluMe

w

For a first volume adjustment, position the CROSSO-
VeR

e

 at around 120 hz, and turn slowly the VOluMe

w

 

clockwise from minimum level up to a position where you 
feel that the subwoofer sound level is appropriate. A check 
of the level adjustment will be necessary after following 
steps.

 

 CRoSSoVeR

e

this potentiometer adjusts the cut-off frequency which 
determines the working bandwidth of the subwoofer. this 
adjustment should be done according to the specifications 
of the main speakers and the room acoustics. Choose the 
best frequency after various listening tests.

 

 PhASe

r

For a better sound integration of the subwoofer in the main 
system, the PhASe

r

 of the subwoofer might have to 

be inverted (180° position), depending on the distance 
between the subwoofer and the main speakers. you have to 
check the PhASe

r

 each time you move your speakers and 

each time you adjust the CROSSOVeR

e

.

Attention, if you use 2 subwoofers, both phase switches 
must be on the same position.
Our web site 

www.cabasse.com

 will give you the speci-

fic adjustments we recommend for the use of our active 
subwoofers.

MAintenAnCe

the Mt31 cabinets are made of medium density fiber panels, 
protected by synthetically veneer with two coats of varnish and 
a special anti-scratch film. this hi-tech veneer does not require 
any specific care. use a wet cotton waste for cleaning, or any 
cleaning device for wood or plastic.

Weee MARK

Disposal of Wastes of electrical & 

electronic equipment (Applicable 

in the european union)

this symbol on the product, consisting of the crossed-out wheeled 
bin, indicates that this product shall not be treated as household 
waste. Instead it shall be handed over to the applicable collection 
point for the disposal of electrical and electronic equipment at the 
end of life.
By ensuring this product is disposed of correctly, you will help prevent 
potential negative consequences for the environment and human 
health, which could otherwise be caused by inappropriate waste han-
dling of this product. the recycling of materials will help to preserve 
natural resources. For more detailed information about recycling of 
this product, please contact your local city office, your household 
waste disposal service or the shop where you purchased the product.

Mt31 

Position 

Ways 

Drivers complement 

Sensivity 

Cross-over 

Frequency 

nominal 

Minimum 

Power 

Peak 

Standard 

Dimensions 

Weight  

 

 

 

 

1W/1m 

points 

response 

impedance 

impedance 

handling 

power 

finish 

h x w x d (cm) 

(kg) 

 

 

 

 

(dB) 

(hz) 

(hz) 

(ohms) 

(ohms) 

(Watt) 

(Watt) 

 

h x w x d (”) 

(lbs)

AntiGuA

 

in wall 

1 x tweeter DOM 36

 

88 

1,800 53-22,400  8 

6.8 

40 

320 

paintable 

32 x 23 x 8,8

 2.2 

in wall

 

  

1 x 17 cm 17t20 IW

 

 

 

 

 

 

 

 

white 

12.6 x 9.1 x 3.5 in 

4.9 lbs

AntiGuA

 

bookshelf/ 2 

1 x tweeter DOM 37

 

89 

2,800 

60-23,000 

4.3 

75 

550 

Wenge / black front grill 

41 x 22 x 30

 9 

main speaker

 

stand  

1 x 17 cm 17tN15

 

 

 

 

 

 

 

 

Maple / black front grill 

16.1 x 8.7 x 11.8 in 

20 lbs

toBAGo

 

floorstanding 2 

1 x tweeter DOM 37

 

87 

2,550 

55-23,000 

4.6 

85 

600 

Wenge / black front grill 

96 x 22 x 32

 17 

main speaker

 

  

2 x 13 cm 13tN15

 

 

 

 

 

 

 

 

Maple / black front grill 

37.8 x 8.7 x 12.6 in 

37 lbs

JeRSeY

 

floorstanding 2 

1 x tweeter DOM 37

 

90 

2,300 

58-23,000 

4.4 

100 

700 

Wenge / black front grill 

100 x 22 x 32

 18 

main speaker

 

  

2 x 17 cm 17tN15

 

 

 

 

 

 

 

 

Maple / black front grill 

39.4 x 8.7 x 12.6 in 

40 lbs

SoCoA

 

on/under 2 

1 x tweeter DOM 37

 

88 

3,000 

64-23,000 

4.5 

85 

600 

Wenge / black front grill 

16 x 47 x 37

 10 

center

 

screen  

2 x 13 cm 13tN15

 

 

 

 

 

 

 

 

Maple / black front grill 

6.3 x 18.5 x 14.6 in 

22 lbs

AlDeRneY

 

floorstanding 3 

1 x tweeter DOM 37

 

90 

850-3,400  59-23,000 

3.5 

110 

770 

Wenge / black front grill 

109 x 23 x 35

 23 

main speaker

 

  

1 x 13 cm 13tN15

 

 

 

 

 

 

 

 

Maple / black front grill 

42.9 x 9 x 13.8 in 

51 lbs 

 

  

2 x 17 cm 17tN15

oRion

 

floorstanding 

1 x 21 cm 21MT3 

active 

adjustable 

35-200 

active 

active 

250 

750 

Wenge  

42 x 30 x 43

 17 

active subwoofer

 

 

 

 

 30-180   

 

 

   

Maple 

16.5 x 11.8 x 16.9 in 

37 lbs

Because of technical improvements already under way in our constant search for optimum quality, 

Cabasse reserves the right to modify all the models presented in specification sheets, advertising materials and manuals without prior notice.

ACtiVe SuBWooFeR oRion Mt31

Pulsed sound pressure 

 

114 dB

Phase switch 

 

0° 

normal

 

 180°  reverse

In put 

 

2 low level - 2 hight level

Voltage 

 

115 / 230 V AC-50 / 60 hz

Maximum power consumption  

165W

Standby power consumtion   

0.49W @ 230VAC 

 

 

0.5W @ 115VAC

Power consumption when off   

0.04W @ 230VAC 

 

 

0.04W @ 115VAC

useable temperature range 

 

+5°C to +35°C

Storage temperature 

 

-5°C to +40°C 

useable humidity range 

 

40% to 70%

Summary of Contents for ALDERNEY MT31

















Reviews: