background image

14

14

15

Control Panel

3.4  Printer States

State

Display

Description

Ready

Ready

The printer is in the ready state and 

can receive data.

Printing Label

Printing Label 

and the number of the 

printed label in the print 

job.

The printer is currently processing 

an active print job. 
Data can be transmitted for a new 

print job. 
The new print job will start when the 

previous one has finished.

Pause

Pause 

and the symbol  

 

The printing process has been 

interrupted by the operator.

Correctable 

error

 

 

and the type of error 
and the number of labels 

still to be printed, 
display flashes red.

An error has occurred that can be 

rectified by the operator without 

interrupting the print job. 
The print job can be continued after 

the error has been rectified.

Irrecoverable 

error

 

 

and the type of error 
and the number of labels 

still to be printed, 
display flashes red.

An error has occurred that cannot 

be rectified without interrupting the 

print job. 

Critical error

 

 

Critical fault

and the type of error, 
display flashes red.

An error occurs during the system 

test.

 

Switch the printer off and then 

on again at the power switch.

Call Service if the fault occurs 

persistently.

Power Save 

Mode

 

 

If the printer is not used for a 

lengthy period, it automatically 

switches to power save mode. 

 

To exit power save mode: Touch 

touchscreen display.

Table 2 

Printer States

Summary of Contents for eos 1





































Reviews: