background image

2

SAFETY
DEFINITIONS

 

!

DANGER

: Indicates a hazardous situation that, if not avoided, will result in death or serious injury�

 

!

WARNING

: Indicates a hazardous situation that, if not avoided, could result in death or serious injury�

 

!

CAUTION

: Indicates a situation that will or could cause minor injury or property damage�

GENERAL PRECAUTIONS

Read the Owner’s Manual before operating�

 

!

DANGER

Do not use compressed air for breathing air applications� 
Beware of high voltage: disconnect lockout/tagout electric supply before servicing� 
Ground compressor per codes�

 

!

WARNING

Beware of high-pressure air: do not bypass, modify, or remove safety/relief valves� 
Beware of hot surfaces: allow unit to cool before servicing� 
Do not operate with safety guards removed�

 

!

CAUTION

Never operate the compressor near flammable liquids or vapors� 
Do not direct the air stream at body� 
Drain tank air weekly to decrease risk of bursting�

NOTE

: Per UL 1450:46�17 C-Aire recommends a maximum of 70% duty cycle for its compressors�

INSTALLATION
SELECTING A LOCATION:

C-Aire compressors are to be installed and operated in a clean, dry, well-lighted, and well-ventilated area�

Provide at least 200 cubic feet of fresh air per 1 hp�

Ideal operating temperatures are between 32°F and 100°F�

Avoid excessively humid areas, as moisture may form in the pump, producing sludge and causing moving parts to wear prematurely�

NOTE

: The dry pipe/sprinkler system compressor is to be installed in accordance with the Standard for Installation of Sprinkler Systems, 

NFPA 13�

 

!

CAUTION

: If temperatures consistently drop below 32° F, install the compressor in a heated area�

 

!

CAUTION

: Never operate the compressor in temperatures below 20°F or above 104°F�

 

!

WARNING

: A compressor should never be used in an area where toxic, corrosive, or volatile agents may be present�

(INSTALLATION CONTINUED ON NEXT PAGE)

Summary of Contents for S244


















Reviews: