byox 108266, Manual

Page: 16 / 17

1. Before first use, make sure the trampoline is correctly assembled and there are no loose parts.
2.
WARNING! Make sure 100% that the zipper is closed before you start jumping.
3. The net is not intended to bounce off of it for higher speed. It is designed to protect the user from falling out of
the trampoline. Intentional jumping into the safety net may cause roll over or damage on the net.
4. Improper use and maintenance of the trampoline and its safety net will void your warranty.
5. Check regularly before use that the safety net is properly fitted. Tighten loose screws or connections if
necessary.
6. Everyone who uses or will use the trampoline must understand and master the basic jumping techniques.
7. Fundamental bouncing techniques:
А. Figure J-A: The basic bounce:
Stand upright. Your legs should be slightly bent and spaced equal to the
width of your shoulders. Your eyes should be focused on the pad. Swing your arms forward and upward, in a
circular motion. Bounce and in mid-air put your feet side by side with your toes pointing downwards.
B. Figure J-B: Braking maneuver: Sometimes you can lose control of your jump. Performing the braking
maneuver will allow you to regain control of your jump and balance. Start with a basic bounce. As you land, bend
your knees sharply and this will allow you to stop your jump.
C. Figure J-C: Hands and Knees Bounce: Start with a low controlled basic bounce. Land on your knees and
arms and your back should be straight. The focus should be on a good 4-point landing, not the jumping height.
D. Figure J-D: Knees Bounce: Start with a low controlled basic bounce. Land on your knees with your back
straight. Your upper body should be upright, use your hands to maintain balance. Bounce back to the basic
bounce position by swinging your arms up.
E. Figure J-E: Seat Bounce : Land in a sitting position. Place your hands on the jump mat, close to your hips.
Push with your hands to stand up and bounce.
ASSEMBLY STEPS
•
WARNING! THE SCHEMES AND FIGURES IN THIS INSTRUCTION ARE FOR ILLUSTRATIVE PURPOSES
ONLY AND THE PRODUCT YOU HAVE BOUGHT MAY DIFFER FROM THEM.
•
NOTE! Two adults in good health must assemble the product.
•Wear gloves and proper clothes and shoes to ensure your safety during the assembly.
•Keep all the packages until you completely assemble the product and make sure there isn’t any part left inside
them. Afterwards throw them away in the designated place.
1.Step 1
– See Figure 1:
Attach the extensions to the legs. Align the holes, designated for the fixing screws.
Slide the screws and fix them using screwdriver.
2.Step 2
– See Figure 2:
Attach the top rails to each other to form a circle. You will need help from another adult
to connect the last 2 rails. One of you must hold the opposite side, while the other connects the two ends.
3.Step 3
– See Figure 3:
Connect the legs (base) to the already assembled frame for the springs. Fix then using
screws.
4.Step 4
– See Figure 4:
Turn the jumping mat so that the seams are facing down. Put the pad in the middle of
the frame. Connect one spring to one of the triangular rings on the mat. Then insert the other end of the spring
into the corresponding opening in the frame. Attach a second spring to the opposite side of the frame. Take 2
springs. Attach the third one in the middle of the frame between the 1
st
and 2
nd
spring. The fourth spring must be
attached to the opposite side of the frame. This way the tension will spread evenly between the springs. Repeat
to attach the rest of the springs. Use the spring fixing tool for this purpose. We recommend you to leave a
distance of 4
– 5 openings between adjacent springs.
Warning! During the spring assembly, be careful not to
pinch your hands or other parts of your body.
5.Step 5
– See Figure 5:
After you attach all the springs, place on top of them their cover. Connect the ties of
the cover under the springs.
6.Step 6
– See Figure 6:
Connect the bottom poles for the safety net to the legs of the trampoline. Use bolts,
washers, nuts, screwdriver and wrench to fix the poles to the legs.
7.Step 7
– See Figure 7:
Slide the upper poles in the pockets of the safety net.
8.Step 8
– See Figure 8:
Attach the upper poles to the bottom poles. Press down until they are securely fixed.
9.Step 9
– See Figure 9:
Slide the pockets of the net and onto the bottom poles so that the net reaches the
frame of the trampoline.
10.Step 10
– See Figure 10:
Strengthen the net and connect the hooks on its bottom ends to the rings on the
bottom part of the jumping mat. The zipper must be facing the base and outwards so that you can easily enter
the trampoline.
PRODUCT USE
15