BYOC Parametric EQ Instructions Manual Download Page 2

Tech Support:

BYOC, LLC makes no promises or guarantees that you will sucessfully complete

your kit in a satisfactory mannor.  Nor does BYOC, LLC promise or guarantee that you

will receive any technical support.  Purchasing a product from BYOC, LLC does not

entitle you to any amount of technical support.  BYOC, LLC does not promise or

guarantee that any technical support you may receive will be able to resolve any or all

issues you may be experiencing.

That being said, we will do our best to help you as much as we can.  Our

philosophy at BYOC is that we will help you only as much as you are willing to help

yourself.  We have a wonderful and friendly DIY discussion forum with an entire section

devoted to the technical support and modifications of BYOC kits.

www.buildyourownclone.com/board

When posting a tech support thread on the BYOC forum, please post it in the

correct lounge, and please title your thread appropriately.  If everyone titles their threads

HELP! , then it makes it impossible for the people who are helping you to keep track of

your progress.  A very brief discription of your specific problem will do.  It will also make

it easier to see if someone else is having or has had the same problem as you.  The

question you are about to ask may already be answered.  Here are a list of things that you

should include in the body of your tech support thread:
1. A detailed explanation of what  the problem is. (not just,   It doesn t work, help )

2. Pic of the top side  of your  PCB.

3. Pic of the underside of your PCB.

4. Pic that clearly  shows your footswitch/jack wiring and the wires going to the PCB

5. A pic  that clearly shows your wiring going from the PCB  to the pots and any other

switches(only if your kit has non-PC mounted pots and switches)

6. Is bypass working?

7.  Does the LED come on?

8. If you  answer yes to 6 and 7, what  does the pedal do when it is "on"?

9. Battery or adapter.(if  battery, is it good? If adapter, what type?)

Also, please only post pics that are in focus.  You're only wasting both parties'

time if you post out of focus, low res pics from your cell phone.

Revision Notes:

Rev 1.0 - no known errors

Copyrights:

All material in this document is copyrighted 2010 by BYOC, LLC

Summary of Contents for Parametric EQ




























Reviews: