BYOC Large Beaver Triangle Instructions Manual Download | Manualshive

Page: 14 / 23

background image

Step 2

: Flip the PCB over so that the bottom or solder side is up. Insert the

three potentiometers, the two toggle switches, and the LED into the bottom
side of the PCB.

DO NOT SOLDER ANYTHING YET!!!

The LED will

have one lead that is longer than the other.

THIS WILL GO INTO THE

SQUARE SOLDER HOLE.

Don’t forget to remove the nuts and washers

from the pots and also to snap off the tabs before you do this step.

«
...
12
13
14
15
16
...
»

Summary of Contents for Large Beaver Triangle
























Reviews:

No comments

Related manuals for Large Beaver Triangle

LITTLE GREEN WONDER

Brand: Mad Professor Pages: 2

Brand: X-keys Pages: 4

Brand: DigiTech Pages: 52

Brand: Fostex Pages: 28

Brand: Life Fitness Pages: 88

Brand: Lithium Grim Pages: 10

Brand: Lithium Grim Pages: 14

Brand: Denon Pages: 32

Brand: Ecler Pages: 36

F Audio Labs Eddie Kramer PHAZEVIBE

Brand: Nembrini Audio Pages: 7

Brand: YORKVILLE Pages: 10

Brand: YORKVILLE Pages: 24

Brand: Rane Pages: 8

Brand: Apogee Pages: 8

Brand: Gemini Pages: 6

Brand: T-Rex Pages: 5

Brand: MA Pages: 47

Brand: Mackie Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands