background image

EN

28

The scope of delivery of the RO device includes:

Microprocessor controller:

1

    OLED display

 (monochrome: blue)

2

    Function button: ON/OFF and standby

3

    Function button: Upward

4

    Function button: Downward

5

    Function button: Confirmation/OK

6

    Status/Alarm LED (

green:

 ready, working, flushing, pause

      

red:

 

service, no feed water, alarm

)

Connections and service components:

7

    Electrical wiring with grounded PE mains plug “CEE7“

8

    Feed water connection 

3/4“ 

male thread

9

    Permeate connection 3/8“ male thread 

10

 

Concentrate connection Ø 8mm

11

 

Service opening for adjusting the pump pressure

Optionally available, Item no. 824047:

12

  External contacts (INPUT/OUTPUT), 3-pin, M8

     for the communication between RO unit and 
     the external unit for external start-/stop switching (DI)
     and alarm output (DO).

1.3 Manufacturer

The RO devices BWT bestaqua 6,12,18 are 

manufactured in the name of:

BWT water + more GmbH

Walter-Simmer-Straße 4

AT-5310 Mondsee

Phone:   +43/6232/5011-0

Fax:   +43/6232/4058

1.4 General comments

Following the instructions in this Installation and Operating  

Manual (IOM) helps the operator to run the reverse osmosis 

BWT bestaqua 6,12,18 reliably and economically. This Ma-

nual (IOM) is part of the device and must be constantly avai-

lable at the place of operation for all assigned staff members.

1.4.1 Reading of the manual (IOM)

The staff must have read and understood this IOM prior to any 

work being carried out. A basic precondition for safe working 

is the adherence to all stated safety and operating instructions.

In  addition,  the  local  accident  prevention  provisions  and  the 

general safety provisions effective at the place of operation are 

applicable. The illustrations in these instructions serve the basic 

understanding  and  can  deviate  from  the  actual  design  of  the 

device. Justified claims cannot be derived from the same.

1.2 Scope of delivery

The reverse osmosis unit BWT bestaqua 6,12,18 

consists of 3 core components:

s¬-EASURING¬AND¬CONTROL¬UNIT
s¬(IGH¬PRESSURE¬PUMP¬
s¬2/¬UNIT

Fig. 1:

 

BWT bestaqua 6,12,18 - Front view of the device

Fig. 2:

 

BWT bestaqua 6,12,18 - Rear view of the device

1

5

4

3

2

10

9

8

7

12

11

6

Summary of Contents for bestaqua 12


























Reviews: