manualshive.com logo in svg

BVM Go Fly Gold F-18C, Assembly And Operating Manual, Page: 2 / 34

Share
Download
BVM Go Fly Gold F-18C Assembly And Operating Manual Download Page 2

 BVM ®2021                                                  1                                                  10/2021 

Contents

 

INTRODUCTION .................................................................................................................. 3

 

DISCLAIMER ....................................................................................................................... 3

 

Recommended Accessories ................................................................................................. 4

 

Required Tools ..................................................................................................................... 5

 

List of Adhesives/Lubricants ................................................................................................. 5

 

Available Options ................................................................................................................. 5

 

WING PREPERATION ............................................................................................................ 6

 

MISSILE RAIL INSTALLATION ............................................................................................... 7

 

STABILATOR PREPERATION ................................................................................................ 8

 

CANOPY AND SERVO REMOVAL ......................................................................................... 9

 

SERVO PLATE REMOVAL ..................................................................................................... 9

 

CANOPY AND SERVO INSTALLATION ............................................................................... 10

 

CANOPY FRAME INSTALLATION ....................................................................................... 10

 

ADJUSTING THE CANOPY .................................................................................................. 11

 

FUEL SYSTEM ...................................................................................................................... 12

 

HEADER TANK MOUNT AND INSTALLATION .................................................................... 13

 

UAT MOUNTING TRAY ........................................................................................................ 14

 

TURBINE MOUNTING FOR TWIN ........................................................................................ 15

 

TURBINE MOUNTING FOR SINGLE .................................................................................... 18

 

WHEEL AND BRAKE PREPERATION ................................................................................. 19

 

RX MOUNTING TRAY AND BATTERY LOCATION ............................................................. 21

 

BATTERY LOCATION ........................................................................................................... 22

 

COCKPIT MOUNTING AND PILOT ...................................................................................... 23

 

PILOT MOUNTING ................................................................................................................ 23

 

INSTALLATION OF THE WINGS AND TAIL ......................................................................... 24

 

WINGS .................................................................................................................................. 24

 

STABILATORS ...................................................................................................................... 25

 

Summary of Contents for Go Fly Gold F-18C



































Reviews:

No comments