background image

SECTION IV

MAINTENANCE

4-1 MAINTENANCE CHECK LIST

Perform  scheduled  maintenance  as  outlined  below.
Lower implement to ground, turn off tractor, and set
parking brake before doing maintenance inspections
or  work.  Some  checks  may  require  raising  machine
off  ground  and  supporting  with  blocks.  All  bolts
should  be  torqued  as  indicated  in  torque  chart
unless otherwise indicated.

WARNING

THE  CUTTER  CAN  FALL  FROM
HYDRAULIC  SYSTEM  FAILURE.  TO
AVOID  SERIOUS  INJURY  OR  DEATH,
SECURELY  SUPPORT  CUTTER  BEFORE
WORKING UNDERNEATH.

BEFORE EACH USE.

1. Check tractor tire air pressure. Refer to tractor

operator’s  manual.  Check  mower  tire  pressure  (if
pneumatic tires). Tire pressure should be 30 psi.

2.  Check  blades  and  spindles  to  be  sure  that  no

foreign objects such as wire or steel strapping bands
are wrapped around them.

3. Check blade bolts for tightness. Tighten blade

bolts to 76 ft./lbs.

4.  Inspect  blades  for  wear.  Replace  if  necessary

per  paragraph  4-5.  Use  only  genuine  Bush  Hog
replacement  parts.  If  it  is  necessary  to  sharpen  the
blades,  remove  the  blades  from  the  spindles  before
sharpening.  DO  NOT  sharpen  blades  while  still
attached to mower.

5.  Make  certain  all  shields  are  in  place  and  in

good  condition.  Repair  or  replace  any  missing  or
damaged shields.

6.  Inspect  wheel(s)  for  wear,  damage  or  foreign

objects. Repair or replace if necessary.

7.  Perform  BEFORE  EACH  USE  lubrication  per

paragraph 4-2.

8.During  operation,  listen  for  abnormal  sounds

which might indicate loose parts, damaged bearings,
or other damage. Correct any deficiency before con-
tinuing operation.

AFTER EACH USE

1. Clean all debris from machine especially under-

side  of  deck,  underneath  belt  shield  and  off  safety
decals. Replace any missing or illegible decals.

2.  Inspect  cutter  for  worn  or  damaged  compo-

nents.  Repair  or  replace  before  next  use.  Any
replacement components installed during repair shall 
include the components’ current safety decals speci-
fied by the manufacturer to be affixed to the compo-
nent.

3. Store cutter in a dry place.

40 HOURS

1.  Check  belt  for  proper  tension.  Refer  to  para-

graph 4-3.

4-2 LUBRICATION

(Figures 4-1A,  & B)

BEFORE EACH USE

1. Driveline Universal Joints - Apply multi-purpose

grease with grease gun.

2.  Driveline  Guard  -  Apply  2-3  shots  of  multi-pur-

pose grease with grease gun to plastic fitting.

3.  Wheels  -  Apply  multi-purpose  grease  wiith

grease  gun.

4. Caster Pivot - Apply multi-purpose grease with

grease gun.

5.  Input  Gearbox  -  Add  EP80W-90  gear  oil,  if

necessary, to bring oil level to check plug.

20 HOURS

6.  Driveline  -  Disconnect  PTO  driveline,  pull  the

two sections apart, thoroughly clean old grease from
tubes and apply thin coat of multi-purpose grease to
outside  of  inner  (male)  section.  Reassemble  sec-
tions  and  install.  Pull  each  section  to  be  sure  drive-
line  and  shields  are  securely  connected.  Make  cer-
tain PTO shielding is in good condition.

NOTE

The  multi-purpose  grease  referenced  in  this

secftion is an NLGI Grade 2 type grease.

Figure 4-1B

(6) 20 Hours

(2) Before Each Use

(1) Before Each Use

11

(4) Before Each Use

Figure 4-1A

(5) Before Each Use

(3) Before Each Use

Summary of Contents for RFM 60





















Reviews: