BUSCH MINK MM 1102 BV, Instruction Manual

Page: 6 / 56

MM 1104, 1144, 1102, 1142 B V ATEX-Version, Gas Tight
page 6
0870141675 /
190709
Transport
Transport in Packaging
Packed on a pallet the vacuum pump is to be transported with a
forklift.
Transport without Packaging
In case the vacuum pump is packed in a cardboard box with inflated
cushions:
♦ Remove the inflated cushions from the box
In case the vacuum pump is packed in a cardboard box cushioned
with rolled corrugated cardboard:
♦ Remove the corrugated cardboard from the box
In case the vacuum pump is laid in foam:
♦ Remove the foam
In case the vacuum pump is bolted to a pallet or a base plate:
♦ Remove the bolting between the vacuum pump and the
pallet/base plate
In case the vacuum pump is fastened to the pallet by means of
tightening straps:
♦ Remove the tightening straps
•
Make sure that the eyebolts are in faultless condition (replace
damaged, e.g. bent eyebolts with a new ones)
•
Make sure that the eyebolts are fully screwed in and tightened
by hand
•
Attach lifting gear securely to the eyebolts on the synchronising
gear (h) and on the drive motor
In case the drive motor comes without an eyebolt or the eyebolt on
the drive motor is located at an unfavourable position:
♦ Loop a belt/rope with suitable length and strength around
the flange of the drive motor
•
Attach the lifting gear to a crane hook with safety latch
•
Lift the vacuum pump with a crane
In case the vacuum pump was bolted to a pallet or a base plate:
♦ Remove the stud bolts from the rubber feet
Storage
Short-term Storage
•
Make sure that the suction connection and the gas discharge
are closed (leave the provided plugs in)
•
Store the vacuum pump
−
If possible in original packaging,
−
indoors,
−
dry,
−
dust free and
−
vibration free.
Conservation
In case of adverse ambient conditions (e.g. aggressive atmosphere,
frequent temperature changes) conserve the vacuum pump
immediately. In case of favourable ambient conditions conserve the
vacuum pump if a storage of more than 3 months is scheduled.
•
Make sure that all ports are firmly closed; seal all ports that are
not sealed with PTFE-tape, gaskets or o-rings with adhesive
tape
Note: VCI stands for “volatile corrosion inhibitor”. VCI-products (film,
paper, cardboard, foam) evaporate a substance that condenses in
molecular thickness on the packed good and by its electro-chemical
properties effectively suppresses corrosion on metallic surfaces.
However, VCI-products may attack the surfaces of plastics and
elastomers. Seek advice from your local packaging dealer! Busch
uses CORTEC VCI 126 R film for the overseas packaging of large
equipment.
•
Wrap the vacuum pump in VCI film
•
Store the vacuum pump
−
If possible in original packaging,
−
indoors,
−
dry,
−
dust free and
−
vibration free.
For commissioning after conservation:
•
Make sure that all remains of adhesive tape are removed from
the ports
•
Commission the vacuum pump as described in the chapter
Installation and Commissioning (
➔
page 6)
Installation and
Commissioning
Installation prerequisites
•
Make sure that the integration of the vacuum pump is carried
out such that the essential safety requirements of the Machine
Directive 2006/42/EC are complied with (in the responsibility of
the designer of the machinery into which the vacuum pump is
to be incorporated;
➔
page 54: note in the E
U
-Declaration of
Conformity)
Mounting Position and Space
•
Make sure that the following ambient conditions will be
complied with:
−
dry and free from corrosion-promoting gases, vapours, mists
and dusts
−
ambient temperature: 0 … 40 °C
−
ambient pressure: atmospheric
CAUTION
In case of non-compliance with the installation prerequisites,
particularly in case of insufficient cooling:
Risk of damage or destruction of the vacuum pump and
adjoining plant components!
Risk of injury!
The installation prerequisites must be complied with.
CAUTION
Do not walk, stand or work under suspended loads.