BUSCH LM 0530 A Retrofit Instructions Download Page 20 | Manualshive

Page: 20 / 24

background image

8 | Troubleshooting

20 / 24

Installation and Retrofit Instructions DOLPHIN LM 0530-0800 A, LT 0320-0630

A_EN_en

8.1 LED Flash Codes

When an error occurs, the LEDs on the variable-frequency drive display a flashing code
that allows the errors to be diagnosed.

The following table contains an overview:

Red LED

Green LED State

Boot loader active (flashing in turn)

Ready for operation (activate En_HW for operation)

Operation / ready

Warning

Error

Identification of motor data

Initialisation

Firmware update

Bus error operation

Bus error ready for operation

Key

LED off

LED on

LED flashing

LED flashing quickly

«
...
18
19
20
21
22
...
»

Summary of Contents for LM 0530 A

























Reviews:

No comments

Related manuals for LM 0530 A

Brand: Walrus Pages: 6

Brand: Walrus Pages: 4

Brand: WarmPool Pages: 26

Delta Solo Compact MVP Series

Brand: KSB Pages: 40

Brand: Kospel Pages: 40

Johnson Pump CombiProLine OH3

Brand: SPX FLOW Pages: 67

SINGLE PACKAGE DUAL FUEL HEAT PUMP

Brand: York Pages: 8

Altherma 3 H F+W EABH16DF9W

Brand: Daikin Pages: 60

Brand: SAMES KREMLIN Pages: 49

EKHWS 150D3V3 Series

Brand: Daikin Pages: 20

Blue Diamond MaxiBlue

Brand: Charles Austen Pages: 20

Brand: K2 Pumps Pages: 24

Ama-Drainer 4 Series

Brand: KSB Pages: 60

Brand: InSinkErator Pages: 16

Brand: Daikin Pages: 52

Brand: foras Pages: 8

cIAPMO-T RV-550

Brand: PrecisionTemp Pages: 8

Brand: AL-KO Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands