manualshive.com logo in svg

Burkert 2301 Series, Operating Instructions Manual, Page: 38 / 48

Share
Download
Burkert 2301 Series Operating Instructions Manual Download Page 38

38

Maintenance, cleaning

Remove control cone

Spindle

Spring-type 

straight pin

Control cone

Seal

Fig.25:

Replacing the control cone set

NOTE! 

Important for impeccable and stable device function! 

The seal surface of the control cone must not be damaged.

Procedure:

 

→

Knock out spring-type straight pin using a suitable pin punch.

 

Pin punch ø 4 mm

, for spindle diameter 10 mm.

 

Pin punch ø 5 mm,

 for spindle diameter 14 mm.

 

→

Remove control cone.

Replacing packing gland

PEEK spindle guide (series-production status until April 2012):

 

→

Unscrew spindle guide using the installation wrench

14)

and an 

open-end wrench.

VA spindle guide SP10/SP14 (series-production status as of 

April 2012):

 

→

Unscrew spindle guide using a modified socket wrench

14)

.

VA spindle guide SP22:

 

→

Unscrew VA spindle guide using an open-end wrench.

Installation wrench

Packing gland

PEEK spindle 

guide

Spindle

Packing gland tube

Series-pr

oduction status up t

o 

April 2012

Fig.26: Replacingthepackinggland(PEEKspindleguide)

8) Theassemblywrenchormodifiedsocketwrenchareavailablefrom

yourBürkertsalesdepartment.

Type 2301

English

Summary of Contents for 2301 Series

















































Reviews:

No comments