manualshive.com logo in svg

Burkert 2301 Series, Operating Instructions Manual, Page: 29 / 48

Share
Download
Burkert 2301 Series Operating Instructions Manual Download Page 29

29

Electrical control unit

9 

ELECTRICAL CONTROL UNIT

The Type 2301 valve can be combined with the following control 

units:

•  Type 8692 

Positioner

•  Type 8694 

Positioner

•  Type 8696 

Positioner

•  Type 8693 

Process controller

The electrical port of the pilot valve or the control units 

is described in the respective operating instructions of 

the pilot valve/control unit.

10 

MAINTENANCE, CLEANING

10.1 

Safety instructions

DANGER!

Risk of injury from high pressure in the system.

 

▶

Before loosening lines and valves, turn off the pressure and 

vent the lines.

Risk of injury due to electric shock.

 

▶

Before reaching into the system,

 

switch off the power supply 

and secure against reactivation.

 

▶

Observe the applicable accident prevention and safety regu

-

lations for electrical devices!

WARNING!

Risk of injury due to improper maintenance work.

 

▶

Maintenance may be carried out by authorised technicians 

only.

 

▶

Use an open-end wrench, never a pipe wrench, to screw the 

valve body or actuator in or out, and observe the tightening 

torque.

Risk of injury due to unintentional activation of the system 

and uncontrolled restart.

 

▶

Secure the system against unintentional activation.

 

▶

Following maintenance, ensure a controlled restart.

Type 2301

English

Summary of Contents for 2301 Series

















































Reviews:

No comments