background image

11

HOT WATER

The same basic steps used to brew coffee or tea can be used to obtain hot 

water by leaving the coffee pod or tea bag/pod out of the pod holder.

CAUTION:

 The water from your BUNN

®

 Pod brewer is approximately  93°C 

(200°F). This is hotter than the hot water from your faucet and must be handled 

with care.

COFFEE FUNDAMENTALS

Brewing delicious coffee is similar to cooking any favorite food. Both require 

a good recipe. Proper coffee making requires quality equipment to precisely 

control water temperature, volume, and brew time. The BUNN

® 

Pod brewer 

assures consistency in your recipe by controlling all of these elements. The only 

variables remaining in the recipe are the amount of coffee and the volume of hot 

water used to extract the desired flavor.

The amount of coffee is generally determined by the pod size. (Pod size can 

vary and is determined by the manufacturer.) The BUNN

®

 Pod brewer will work 

with most coffee pods in the 45 - 61 mm range. NOT for use with Espresso pods!

Hot water extracts many elements from the coffee, some desirable, some 

not. The amount of coffee used and the amount of water passed through the 

coffee determines strength. Increasing the amount of coffee (by using a larger 

pod) results in a stronger beverage. Decreasing the amount of coffee (by using 

a smaller pod) with the same amount of water, results in a weaker beverage. Too 

much water and too little coffee can result in over-extraction. Over-extracting the 

coffee can cause an unwanted bitter taste.

As the amount of coffee decreases, you’ll note an increase in the bitterness 

of the beverage. This happens because the hot water begins to remove the 

undesirable elements after all of the desirable elements have  been extracted.

Fresh coffee gives the best results. Always store the coffee pods in a sealed, 

air tight container. Store in a cool, dry area away from other food items with 

strong odors. 

BREWING TIPS

When  properly  brewed,  the  difference  between  the  best  quality  coffee  and  a 

poor  quality  coffee  becomes  very  dramatic.  Proper  brewing  requires  little  effort 

with the BUNN

®

 Pod brewer.

You’ll always have a great coffee experience if you follow these tips:

1)  Always start with clean equipment.
2)  Always use fresh cold water.
3) 

Adjust the recipe until it suits you. If you need to make a stronger cup of 

coffee, experiment with less water or larger pods. The serving size range is 

118 to 355 ml (4 to 12 oz.) as indicated on the Volume Control Indicator.

Summary of Contents for MCPA





















Reviews: