background image

6

ELECTRICAL REQUIREMENTS

WARNING - If the power cord is ever damaged, it must be replaced by the manufacturer or its service agent with 

a special cord available from the manufacturer or its service agent in order to avoid a hazard.
CAUTION - The dispenser must be disconnected from the power source until specified in Electrical Hook-Up.
The 120 volt version of this dispenser has an attached cordset. The mating connector must be a NEMA 5-15R.
Refer to the dispenser’s dataplate for exact voltage requirements.
To access terminal block for high voltage models without a cord set, remove left side panel.

ELECTRICAL HOOK-UP

CAUTION – Improper electrical installation will damage electronic components.

1.  An electrician must provide electrical service as specified.

2.  Using a voltmeter, check the voltage and color coding of each conductor at the electrical source.

3.  Place the ON/OFF/NIGHT switch in the “ON” position.

4.  Connect the dispenser to the power source. 

5.  If plumbing is to be hooked-up later be sure the dispenser is disconnected from the power source. If plumb-

ing has been hooked-up, the dispenser is ready for Initial Fill & Heat.

CE REQUIREMENTS

• This appliance must be installed in locations where it can be overseen by trained personnel.

• For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C.

• Appliance shall not be tilted more than 10° for safe operation.

• An electrician must provide electrical service as specified in conformance with all local and national codes.

• This appliance must not be cleaned by water jet.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental 

capabilities, or lack of experience and knowledge, unless they have been given instructions concerning use of 

this appliance by a person responsible for its safety.

• Children should be supervised to ensure they do not play with the appliance.

• If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel 

with a special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard.

• Machine must not be immersed for cleaning.

230V AC 

single phase models

Note: This electrical service 

consists of 2 current carry-

ing conductors (L1 and L2) 

and a separate conductor 

for earth ground.

GREEN

GREEN

230V. A.C.

BLK

WHI

L1

L2

GRN/YEL

GRN/YEL

45304.1 090611

Summary of Contents for IMIX 14


















Reviews: