background image

8

APPROXIMATE TIMER SETTINGS IN SECONDS

 

 Weight 

   Fine 

   Drip 

Regular

 

(ounces) 

   (7*) 

   (8*) 

  (12*)

 

1.5 0.5 0.5 0.5

 

1.75 0.7 0.6 0.6

 

2.0 1.0 0.8 0.8

 

2.25 1.4 1.4 1.2

 

2.5 1.9 1.8 1.6

 

2.75 2.4 2.2 2.0

 

3.0 2.9 2.7 2.5

 

3.25 3.3 3.1 2.9

 

4.0 4.8 4.4 4.0

 

6.0 8.6 7.9 7.5

 

8.0  12.0 11.5 10.9

 

10.0 15.7 15.1 14.1

 

12.0 19.6 18.5 17.5

 

14.0 23.5 22.0 20.9

 

16.0 27.0 25.3 24.3

*Hash mark settings.  Refer to Adjustment-Burr section.

3.  Use the table on the next page to find approximate timer setting for the grind and amount of coffee de-

sired.

4.  Plug-in the grinder. Select either the right or left hopper with the selector switch. Do not press the start 

switch.

5.  If grinder has an analog timer, proceed to step 6. If grinder has a digital timer, momentarily press the center 

(DISPLAY) button on the dispense timer panel. The readout will indicate the present timer setting in seconds 

and will remain displayed for five minutes.

6.  Adjust the timer setting to obtain the desired amount of coffee for the selected hopper.

7.  Verify the setting by weighing a few samples. Use the following table as an approximate guide only.

8.  Repeat steps 4 thru 7 for the other hopper.

ADJUSTMENTS (cont.)

10218 091708

Summary of Contents for G9-2 HD









Reviews: