background image

Page 8

FACTORY DEFAULTS
NO                      YES

AutoPOD BREWER

VERSION     xx.xx

TEST SWITCHES allows testing of the membrane switches.

   TEST SWITCHES  ?

NO                      YES

AIR PUMP

Activates the air pump motor for the brew tank.

AIR PUMP

 ON    NEXT    OFF

WATER INLET

Activates the water inlet valve for the brew tank, and flow meter count.

         WaterInIet          #

 ON    NEXT    OFF

HOT WATER

Activates the water inlet solenoid for the hot water tank.

 HOT WATER

 ON    NEXT    OFF

VENT VALVE

Activates the vent solenoid for the hot water tank.

 VENT VALVE

 ON    NEXT    OFF

WATER PUMP

N/A

 WATER PUMP

 ON    NEXT    OFF

HOT WATER AIR PUMP

Activates the air pump motor for the hot water tank.

HotWaterAir PUMP

 ON    NEXT    OFF

TANK HEATER

Activates the triac/relay on the main control board for the brew tank heater.

TANK HEATER

 ON    NEXT    OFF

Press the hidden program switch to go back to previous screen. Pressing any 

other membrane switch will give corresponding readout for that switch.

FACTORY DEFAULTS

Reset all brew settings, calibrations back to factory presets.

Requires following "INITIAL SETUP" procedure.
EXIT PROGRAM MODE TO MAIN SCREEN

Model:

Software version:

411701 061308

FACTORY BLOWOUT
NO                      YES

FACTORY BLOWOUT

Used for tank draining.

PROGRAM SWITCH

TO EXIT

Summary of Contents for AUTOPOD BREWER










Reviews: