background image

Page 6

SKU 91309

For technical questions, please call 1-800-444-3353.

Maintenance

(-) Negative

(+) Positive

FIGURE 5

1.  Always turn off the power and disconnect the unit when not in use.
2.  Wipe all of the components to remove any moisture after each use.
3.  Make sure the terminal contacts on the Battery (4) are clean and free of corrosion.
4.  After six hours of use, charge the Battery (4) following the directions below.
5.  Keep the Camera (1) lens clear of dirt or debris.

Battery Charging
Connect the two clips of the Charger (7) to the corresponding positive and negative terminals
on the Battery (4).  Plug the Charger (7) plug into the power outlet.  The indicator on the
Charger (7) will stay red until the charge is complete.  Once the charge is complete, the
indicator will turn green.  Promptly unplug the unit from the power outlet and remove the clips
from the terminals.  Do not overcharge the battery; overcharging can result in damage to
or acid leaking from the battery.

Never reverse the polarity when connecting the Battery (4) for charging it or running
the system.
  The Red (+) terminal must be attached to the Red (+) clip on the Battery Cord
(5), and the Black (-) terminal must be attached to the Black (-) clip.  See FIGURE 5.

Troubleshooting
If the system is not operating properly, by displaying a rolling, shrunk, or unstable picture,
check all of the connections.  Next, make sure the Battery (4) is fully charged.  Also, check to
make sure the fuse on the Battery (4) is good. If the system still does not work properly, take
the system to an authorized service technician.

Battery (4)

Adapter (7)

Summary of Contents for 91309








Reviews: