1.
Locate a key-on fuse.
a. It only has power when the key is in the “on”
(or “run”) position.
b. Use a 12 volt test light or your vehicle owner’s
manual to locate one.
2.
Remove the fuse
3.
Locate the unpowered (accessory)
side of the fuse socket.
a. With the key on the “run” (or “on”)
position, insert the probe of a 12 volt test
light into each side of the fuse socket.
b. Mark the side that does not light up.
4.
Connect the power cable to the
fuse box.
a. Crimp the fuse spade onto the
power wire.
b. Slide the fuse tap over one
metal prong of the fuse.
c. Slide the fuse spade over the fuse tap.
d. Put the tapped fuse back in the fuse box;
make sure that the tapped side of the fuse is
placed in the unpowered (accessory) side of
the fuse socket (see step 3).
The black ground wire inside the power cable is not required.
5.
Connect the power cable to the adapter
6.
Slide the adapter plug switch to KEY.
7.
Run the HDMI cable under the dash or
weather stripping.
This is discreet, stylish and will help protect the GT.
8.
Mount the GT
a. Select a safe place to mount the GT.
1. Make sure not to obstruct the driver’s view.
2. Make sure that the HDMI cable can reach
the GT with a small amount of slack.
The windshield should be clean and dry.
b. Use the T-slot on the back of the GT to attach
it to the Universal Windshield Mount (UWM).
c. Position the UWM suction cup on the
windshield and press the lever on the base of
the mount towards the windshield to secure
it in place.
G
:
COMPLETE PHYSICAL INSTALLATION
Steps 1-4 will enable the vehicle key position to control the power state (on/off) of
the GT; if you do not want the GT to automatically power on and off according to
the key position, skip steps 1-4.
E
:
PRE-TUNE CHECKLIST
CONNECT THE GT TO THE VEHICLE
D
:
OBDll Port Location
All OBDll ports are located under the
dash on the drivers side of the vehicle.
Complete physical installation is not required to install the tune to the vehicle. To use
features like automatic (ignition-controlled) power on/off and the Driving Coach,
complete installation is recommended. Instructions for complete installation are
located in section G.
1.
Connect the adapter plug to the
vehicle diagnostic port (OBDII).
The port is located under the dash on the
driver’s side.
2.
Slide the power switch on the adapter
plug to BAT.
The GT should turn on.
3.
Connect the GT to the adapter plug.
a. Use the HDMI cable.
b. Do NOT use the USB cable.
1.
Check fuses
(GM Vehicles Only)
Check the included red fuse card and remove
fuses before installing the tune. (Replace the
fuses after the download is complete.)
2.
Check your battery
Before installation, ALWAYS ensure that the
batteries are fully charged. If you are not sure,
connect a battery charger before you begin
installing the tune.
3.
Turn electronics OFF
Leaving electronics on (stereo included) may
prevent a successful download.
4.
The download
Do not interrupt or disconnect the GT at any
point during the download. Leave electronics
off during the entire process.
F
:
1.
Turn the key to the “on” (or “run”) position.
a. Do NOT start the engine.
2.
Go to the Main Menu (top left button).
3.
Choose
Install Download
.
4.
Follow the instructions on the GT screen.
a. You will be prompted to turn your key to the “off” or “on”
position and then press Continue.
b. Do NOT start the engine when turning the key to the
“run” (or “on”) position at any time during the download.
c. You may be prompted to make choices about vehicle-
specific settings such as the speed limiter. The GT
owner’s manual (available online at
www.bullydog.com
)
has more information on these settings.
5.
After the installation replace any removed fuses.
INSTALL THE TUNE
or
The key-on fuse should be either a 10
or 15 amp fuse
Bully Dog r
ecommends installing during business hours: Monday-Friday 7am-6pm MST
. Bully Dog technical support: 940-783-9915
Bully Dog recommends installing during business hours: Monday-Friday 7am-6pm MST. Bully Dog technical support: 940-783-9915
Bully Dog recommends installing during business hours: Monday-Friday 7am-6pm MST. Bully Dog technical support: 940-783-9915
Bully Dog r
ecommends installing during business hours: Monday-Friday 7am-6pm MST
. Bully Dog technical support: 940-783-9915
Doc. #40410-289 v5.4
When doing future software updates be sure to go
to “return to stock” from the main Menu
