background image

SYSTEM FEATURES

SYSTEM COMPONENTS

TECHNICAL ASSISTANCE

Should you need help. First check our website at www.bulldogsecurity.com/wires.htm or call our toll-free

Tech Support Hotline Monday through Friday 9AM-8PM and Saturday 10AM-4PM EST at 800-878-8007.

You must give the following information:

•Name

•Telephone Number with Area Code (Fax number if applicable)

•Year, Make, and Model of the vehicle

•The model number of the system you are installing

•The type of assistance you are requesting

If you give the above information you will be called back as soon as possible, usually within 10 minutes.

1

Four-Button Extended Range

Remotely start your car to run the heater or air conditioning from an extended distance.

Remote Control

Keyless Entry

Remotely locks and unlocks your power door locks.

Trunk Release

Remotely opens your trunk with a push of a button. (Optional part #775 required)

Remote Programmable Run Time

Remotely program your vehicle to run 5 to 15 minutes. 

Run Time Confirmation

Lets you check the run time that the unit is programmed for.

Tach/Tachless Option

A programmable feature that lets you choose from the easy to install tachless operation or

the standard wire-in, tach operation.

Parking Light Confirmation

Confirms that your vehicle has received a remote signal and will remain on if the engine is

remotely started.

Dome Light Supervision

Never walk up to a dark vehicle again. When unlocking the vehicles doors by remote control

 

the dome light will come on and stay on for 1 minute, or until you activates the ignition 

switch. (Optional part #775 required)

Cold Start 

Remotely program your car to start at a preset temperature. Automatically starts your car in

freezing temperature so you never have a dead battery.

Pit Stop Mode

Allows you to exit the vehicle while the engine remains running.

Extended Range Antenna

Allows you to operate your system from up to 400 feet away. (800 feet for E Models)

Code Learning

Allows your remote starter to learn new remotes, should you want to add remotes, or if remotes

are lost.

Limited Lifetime Warranty

Guarantees life-long protection.

Your system includes:

1-Installation & Operation Guide

1-Main Control Module

1-Four Button Remote Transmitter with Slide Protector

1-(4) Relay Harness with Relays

1-18-Pin Wire Harness

1-Hood Pin Switch

1-Extended Range Antenna (E Models Only)

REQUIRED TOOLS

2-Window Clips

(E Models Only)

1-Warranty

1-Warning Sticker

  for Under the Hood

2-Bulldog Window Decals

You will need a computer-friendly test light and a 5/16 drill bit when mounting the hood pin switch. In

most cases no additional tools are required, however if the bottom of your dash on the driver’s side will

come off you must remove it. In this case a screwdriver or socket set may be needed.

Summary of Contents for RS102












Reviews: