background image

CONTENTS

REMOTE STARTER

MODELS RS102/RS102E, RS112/RS112E, RS122/RS122E

INSTALLATION GUIDE

OWNER’S GUIDE

System Features ......................................1

System Components ....................................1

Required Tools .......................................1

Technical Assistance .................................1

Before You Begin .....................................2

Precautions ..........................................2

Testing Your Wires ...................................2

Making Connections .................................2-4

Locating & Making Connections ......................4-5

Neutral Safety Switch ................................5

Connecting 18-Pin Harness ............................6

Connecting 4-Relay Harness ...........................6

Antenna Placement ....................................6

Anti-Theft System ....................................7

Optional Connections ...............................7-9

Operating Instructions ...............................9

Programming Instructions ..........................9-10

Technical Assistance

All tech personnel are expertly qualified to answer any technical questions.

Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.

Address

288 Canton Avenue • Wintersville, Ohio 43953

Telephone

Phone:  740-264-4710 • 800-878-8007 • Fax: 740-264-7306

Summary of Contents for RS102












Reviews: