background image

authorization for Returned goods

IMPORTANT: BULLARD WILL DECLINE TO ACCEPT ANY RETURNED GOODS SHIPMENT 

UNLESS YOU HAvE FIRST FOLLOWED ALL OF THE STEPS OUTLINED BELOW.
To return goods to Bullard for repair, or replacement, whether under the terms of 

Bullard’s warranty provisions or for paid repairs, you MUST:

1.  Contact Bullard’s Customer Service Department by telephone or in writing at:

BULLARD

1898 SAFETY WAY

CYNTHIANA, kY 41031-9303

TOLL-FREE: 877-BULLARD (285-5273)

PHONE: 859-234-6616

FAx: 859-234-8987
Describe the nature of the problem you are experiencing. A Bullard Customer 

Service Representative may contact you for additional information or may 

attempt to help you resolve the problem over the telephone.

2.  Upon determining that the product should be returned, Customer Service will 

provide you with written permission to return the product to Bullard. This will 

include information which must be included on the shipping carton for proper 

receiving and handling by Bullard. DO NOT return product without first following 

this procedure.

3.  Prior to packing the product for return shipment to Bullard, be certain that 

it has been fully decontaminated and cleaned of any hazardous materials 

which may have settled on the product during use. It is against the law to 

ship hazardous or contaminated materials. Bullard may refuse to accept the 

return of any product suspected of being contaminated.

4.  Products returned, including those under warranty, must be shipped with all 

transportation charges prepaid. Bullard cannot accept any returned products 

delivered on a “freight-collect” basis.

5.  Material returned will be subjected to factory inspection.  Repair work that is 

deemed necessary, but which is not covered by warranty, will be performed at 

your expense. Bullard will attempt to provide a best estimate of such charges, 

but will invoice based upon work performed.

Routine air filter Replacement schedule

caRbofine outlet filteR caRtRidge

(cat. no. s17101)

MediuM efficiencY inlet filteR

(cat. no. 23611)

Cumulative Pump 

Operating Hours

Last Filter 

Replacement Date

Employee Responsible 

(Initials)

Pump Operating Hours

Cumulative Last Filter 

Replacement Date

Employee Responsible 

(Initials)

200

500

400

1,000

600

1,500

800

2,000

1,000

2,500

1,200

3,000

1,400

3,500

1,600

4,000

1,800

4,500

2,000

5,000

©2013 Bullard. All rights reserved.
Free-Air is a registered trademark of Bullard

6094000015B (0913)

ISO 9001 

certified

americas:

bullard

1898 Safety Way  
Cynthiana, KY  41031-9303 • USA
Toll-free within USA: 877-BULLARD (285-5273)
Tel: +1-859-234-6616 
Fax: +1-859-234-8987

europe:

bullard gmbh

Lilienthalstrasse 12
53424 Remagen • Germany
Tel: +49-2642 999980 
Fax: +49-2642 9999829

asia-Pacific:

bullard asia Pacific Pte. ltd.

LHK Building
701, Sims Drive, #04-03 
Singapore 387383
Tel: +65-6745-0556 
Fax: +65-6745-5176

www.bullard.com

Summary of Contents for Free-Air ADP3CA









Reviews: