Bullard ADP20 Instruction Manual Download Page 18

AIR FILTER REPLACEMENT SCHEDULE

Regular inspection and replacement of the Air Filters will prevent extensive and costly pump
repairs. Dirty or clogged filters can be responsible for failure of the pump to build up outlet pres-
sure and eventual overheating.

– Replace the Carbofine Outlet Filter Cartridge (Cat. No. S17101) at least once every 200 run-

ning hours or sooner if necessary.

The Outlet Filter Cartridge is multi-layered with 40-micron size particles of activated carbon, a
sorbent bed with an exposed carbon surface of more than 15,000 square feet.

Vapor Removal Efficiency: 90-95%

D.O.P. Efficiency: (0.3 to 0.6 Micron Particles) 99.97%

Solid Particle Filtering: 0.2 Micron and Larger.

Liquid Particle Filtering: 0.75 Micron and Larger

– Replace the medium efficiency Inlet Filter (Cat. No. 23611) at least once every 500 running

hours or sooner if necessary.

The Inlet Filter keeps moisture as well as particulates larger than 25 micron out of the air
supply and helps protect the pump’s carbon vanes.

We recommend the following chart be used to monitor and maintain a routine Air Filter replace-
ment schedule.

CARBOFINE OUTLET FILTER CARTRIDGE

MEDIUM EFFICIENCY INLET FILTER

(Cat. No. S17101)

(Cat. No. 23611)

Cumulative 

Cumulative

Pump

Last Filter

Employee

Pump

Last Filter

Employee

Operating

Replacement

Responsible

Operating

Replacement 

Responsible

Hours

Date

(Initial)

Hours

Date

(Initial)

200

500

400

1,000

600

1,500

800

2,000

1,000

2,500

1,200

3,000

1,400

3,500

1,600

4,000

1,800

4,500

2,000

5,000

16

Summary of Contents for ADP20





















Reviews: