Buhler SCS 104 Installation And Operation Instructions Manual Download Page 19 | Manualshive

Page: 19 / 75

background image

SCS 104

5.7 Flow Meter Operation

The flow meters have a range of 50..500 L/h. The flow can be controlled with the built-in valves.

The flow meters are calibrated for air at 20 °C (68 °F) and 1.2 bar (17.4 psi) abs. Actual values may therefore vary when using other
calibrating and sample gases.

5.8 Pressure regulators and gauges

Blowback air pressure is controlled by a regulator (18) on the front panel. To adjust the pressure pull the regulator knob out to
unlock it and turn counter clockwise to decrease the pressure or clockwise to increase the pressure. When the desired pressure
has been obtained, push the knob in to lock it.

The set value is shown on a gauge (19).

17

Bühler Technologies GmbH

BECS0031 ◦ 02/2020

«
...
17
18
19
20
21
...
»

Summary of Contents for SCS 104












































































Reviews:

No comments

Related manuals for SCS 104

Brand: Kawai Pages: 5

Brand: Jata hogar Pages: 12

Brand: Igema Pages: 30

Brand: z-laser Pages: 62

Brand: Eaton Pages: 87

Brand: Eaton Pages: 16

Brand: janitza Pages: 6

Brand: janitza Pages: 36

Zetasizer Nano Series

Brand: Malvern Pages: 16

Brand: Abus Pages: 168

Brand: OHAUS Pages: 76

Brand: Mini Pages: 20

Brand: PICO Pages: 2

Brand: Omega Pages: 20

Brand: Keithley Pages: 338

CR-2010 PRO Series

Brand: G-Tek Pages: 48

Brand: Charder Pages: 12

Brand: QUNDIS Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands