background image

BA 4000 Inj.

2.2 General hazard warnings

Installation of the device shall be performed by trained staff only, familiar with the safety requirements and risks.

Check all relevant safety regulations and technical indications for the specific installation place. Prevent failures and protect
persons against injuries and the device against damage.

The operator of the system must secure that:

– safety and operation instructions are accessible and followed,

– local safety regulations and standards are obeyed,

– performance data and installation specifications are regarded,

– safety devices are installed and recommended maintenance is performed,

– national regulations for disposal of electrical equipment are obeyed.

Maintenance, Repair

Please note during maintenance and repairs:

– Repairs to the unit must be performed by Bühler authorised personnel.

– Only perform conversion-, maintenance or installation work described in these operating and installation instructions.

– Always use genuine spare parts.

Always observe the applicable safety and operating regulations in the respective country of use when performing any type of
maintenance.

DANGER

Electrical voltage

Electrocution hazard.

a) Disconnect the device from power supply.

b) Make sure that the equipment cannot be reconnected to mains unintentionally.

c) The device must be opened by trained staff only.

d) Regard correct mains voltage.

DANGER

Toxic, acidic gasses

Sample gas / calibrating gas can be harmful.

a) If necessary, ensure a safe gas discharge.

b) Switch off the gas supply before performing maintenance and protect from opening

inadvertently.

c) Protect yourself from toxic / corrosive gasses when performing maintenance. Wear

appropriate protective equipment.

DANGER

Potentially explosive atmosphere

Explosion hazard if used in hazardous areas.
The device is not suitable for operation in hazardous areas with potentially explosive at-
mospheres.
Do not expose the device to combustible or explosive gas mixtures.

4

Bühler Technologies GmbH

BE550004 ◦ 07/2016-2

Summary of Contents for 55 11 399
























Reviews: