Bug-O Systems K-BUG 1200 Instructions And Parts Manual Download

Page: 16 / 20

KBUG-4010 CARRIAGE ASSEMBLY / PARTS LIST

ITEM

QTY

PART NO.

DESCRIPTION

KBUG-4011

Body, Rear

KBUG-4012

Body Side, Left

KBUG-4013

Body, Bottom

KBUG-4014

Body Side, Right

KBUG-4015

Body, Top

KBUG-4028

Body Cover

KBUG-4032

Handle

KBUG-4027

Magnet, Small

KBUG-4024

Magnet Bracket (1)

KBUG-4029

Sensor Cover

KBUG-4031

Sensor

KBUG-4034

Magnet, Large

KBUG-4026

Magnet Plate

KBUG-4025

Magnet Bracket (2)

KBUG-4023

Motor Bracket (BD)

KBUG-4037

Geared Motor

KBUG-4038

Motor Bracket (BLDC)

KBUG-1049

DC Brushless Motor

KBUG-4021

Wheel Shaft Bushing (2)

KBUG-4035

Chain Sprocket

KBUG-4017

Wheel Shaft Cover (1)

KBUG-4022

Chain

KBUG-4016

Wheel Shaft

KBUG-1036

Wheel, 50mm

KBUG-4018

Wheel Shaft Cover (2)

KBUG-4019

Wheel Shaft Bushing (1)

KBUG-4036

Roller Bearing

Summary of Contents for K-BUG 1200





















Search results

Summary of Contents for K-BUG 1200

Reviews:

Related manuals for K-BUG 1200

Brands by name

Popular brands

Bug-O Systems K-BUG 1200, Instructions And Parts Manual

Search results

Summary of Contents for K-BUG 1200

Reviews:

Related manuals for K-BUG 1200

Brands by name

Popular brands