background image

Specifications

Compliance

Model 

Voltage 

UV 

Power

Dimmensions (mm) 

Weight (kg) 

Width 

Depth 

Height 

FS130 

220-240V

50Hz

8W

15W 

430 

480 

400 

18.1 

FS131 

2*8W 

25W 

430 

480 

825 

32.1 

FS132 

2*15W

40W 

600 

600 

1800 

76.6 

BUFFALO parts have undergone strict product testing in order to comply 

with regulatory standards and specifications set by international, 

independent, and federal authorities. 

BUFFALO products have been approved to carry the following symbol:

All rights reserved. No part of these instructions may be produced or transmitted in any form or by any 

means, electronic, mechanical, photocopying, recording or otherwise, without the prior written 

permission of BUFFALO.

Every effort is made to ensure all details are correct at the time of going to press; however, BUFFALO 

reserve the right to change specifications without notice.

The WEEE logo on this product or its documentation indicates that the product must not 

be disposed of as household waste. To help prevent possible harm to human health 

and/or the environment, the product must be disposed of in an approved and 

environmentally safe recycling process. For further information on how to dispose of this 

product correctly, contact the product supplier, or the local authority responsible for 

waste disposal in your area.

9

Summary of Contents for FS130













Reviews: