Buffalo DW464 Instruction Manual Download Page 2

Safety Tips 

 

 

Position on a flat, stable surface.  

 

A service agent/qualified technician should carry out installation and 
any repairs if required. Do not remove any components on this 
product.  

 

Consult Local and National Standards to comply with the following:  

 

Health and Safety at Work Legislation  

 

BS EN Codes of Practice  

 

Fire Precautions  

 

IEE Wiring Regulations  

 

Building Regulations  

 

DO NOT immerse the appliance in water.  

 

Always switch off and disconnect the power supply to the appliance 
when not in use.  

 

Not suitable for outdoor use.  

 

Keep all packaging away from children. Dispose of the packaging in 
accordance to the regulations of local authorities.  

 

Children should be supervised to ensure they do not play with, or 
operate the Glass Washer 

 

The function of this Glass Washer is the washing of Glasses and similar 
ONLY. 

 

Do not use cleaning agents that contain Chlorine, Bleach or 
Hypochlorite 

 

Only use commercial grade detergents and rinse aids in your Glass 
Washer 

 

Wear the correct personal protective equipment when handling 

chemicals and observe all safety notes 

 

Damage to the Glass Washer caused by lime scale or poor water 
quality will NOT be covered by the manufacturers warranty – fitting of 
a water softener is recommended 

 

The installer and user are responsible for ensuring the installation and 
operation of this Glass Washer 

 

Ensure the base of the unit is never submerged or standing in water 
when operating the Glass Washer  

 

Do not use electrical extension lead(s) to supply power to your Glass 
Washer 

 

If the power cord is damaged, it must be replaced by a BUFFALO agent 
or a recommended qualified technician in order to avoid a hazard.  

 

This appliance can be used by children aged from 8 years and persons 

with reduced physical, sensory or mental capabilities or lack of 
experience and knowledge if they have been given supervision or 
instruction concerning use of the appliance in a safe way and if they 
understand the hazards involved. Children shall not play with the 

appliance.  Cleaning and user maintenance shall not be made by 
children without supervision. 

 

Summary of Contents for DW464





















Reviews: