manualshive.com logo in svg

Buffalo DW464, Instruction Manual

Share
Download
Buffalo DW464 Instruction Manual Download Page 12

 

PROBLEM 

CAUSE 

SOLUTION 

The finish washing 

result is  inadequate 

 

 

The suction of the liquid detergent-
rinse aid doesn’t take place 
according to the recommendation 

of the manufacturer     

Check both the peristaltic 
pumps and regulate them 
according the 

recommendation of the 
manufacturer of the 

machine and the 
manufacturer of the 
detergent-rinse aid  

The hardness of the water is 
higher than 9 degree clark 

Communicate with your 
water provider to learn 

about the hardness of the 
water of your area. A 
water softener may be 

fitted 

There is too much foam 

The machine isn’t warming 

sufficiently 

Check if the warming 

indication has gone out or 

is still on 

Foaming detergent been used 

 always use

 non-foaming

 

detergent for ware 

washing machines 

There is incorrect regulations to 

the peristaltic pumps 

Regulate them according 

the recommendation of 

the manufacturer of the 

machine and the 

manufacturer of the 

detergent-rinse aid  

 

 

 

 

Summary of Contents for DW464





















Reviews:

No comments

Brands by name

Popular brands

Load more brands