manualshive.com logo in svg

Buell 2002 X1, Handbook

Share
Download
Buell 2002 X1 Handbook Download Page 346

6-10

2002 Buell X1: Drive/Transmission

HOME

PRIMARY DRIVE/CLUTCH

6.5

GENERAL

The  purpose  of  the  clutch  is  to  smoothly  disengage  and
engage the engine from the rear wheel for starting, stopping
and shifting gears.

See 

Figure 6-13.

 The clutch is a wet, multiple-disc clutch with

six steel plates (1), one spring plate (2) and eight fiber (fric-
tion) plates (3) stacked alternately in the clutch shell (4). The
order  of  plate  assembly,  from  inboard  to  outboard,  is  as  fol-
lows:

F - St - F - St - F - St - F - 

Sp 

- F - St - F - St - F - St - F

(F = Fiber plate, St = Steel plate, 

Sp

 = Spring plate)

The fiber plates (clutch driving plates) are keyed to the clutch
shell  (4),  which  is  driven  by  the  engine  through  the  primary
chain. The steel plates (clutch driven plates) and the centrally
located spring plate (also a clutch driven plate) are keyed to
the  clutch  hub  (5),  which  drives  the  rear  wheel  through  the
transmission and secondary drive belt.

When the clutch is engaged (clutch lever released), the dia-
phragm  spring  (7)  applies  strong  inward  force  against  the
pressure plate (6). The pressure plate then presses the clutch
plates (1, 2 and 3) together, allowing no slippage between the
plates  and  causing  the  plates  to  turn  as  a  single  unit.  The
result is that the rotational force of the clutch shell (4) is fully
transmitted  through  the  “locked”  clutch  plates  to  the  clutch
hub (5). As long as the transmission is set in a forward gear,
power from the engine will be transmitted to the rear wheel.

When the clutch is disengaged (clutch lever pulled to left han-
dlebar  grip),  the  pressure  plate  (6)  is  pulled  outward  (by
clutch cable action) against the diaphragm spring (7), thereby
compressing  the  diaphragm  spring. With  the  pressure  plate
retracted, strong inward force no longer squeezes the clutch
plates (1, 2 and 3) together. The fiber plates (3) are now free
to rotate at a different relative speed than that of the steel (1)
and  spring  (2)  plates  (i.e.  –  slippage  between  the  clutch
plates  occurs).  The  result  is  that  the  rotational  force  of  the
clutch  shell  (4)  is  no  longer  fully  transmitted  through  the
“unlocked”  clutch  plates  to  the  clutch  hub  (5). The  engine  is
free to rotate at a different speed than the rear wheel.

Figure 6-13. Clutch Plates and Hub/Shell Assembly

1

6249

3

2

4

5

1.

Steel Plate (6)

2.

Spring Plate

3.

Fiber Plate (8)

4.

Clutch Shell

5.

Clutch Hub

6.

Pressure Plate

7.

Diaphragm Spring

Clutch 

disengaged

b0422x6x

7

6

3

Clutch 

engaged

2

1

5

4

Table 6-1. Clutch Troubleshooting

SYMPTOM

CAUSE (CHECK IN FOLLOWING ORDER)

REMEDY

Clutch slips.

Incorrect clutch release adjustment. 
Worn clutch plates.

Check and adjust clutch release mechanism.
Check service wear limits. Replace plates.

Clutch drags.

Incorrect clutch release adjustment. 
Worn clutch release ramps or balls.
Warped clutch steel plates.
Blade worn or damaged clutch gear splines.
Overfilled primary.

Check and adjust clutch release mechanism.
Replace release ramps and/or balls.
Replace clutch steel plates.
Replace clutch gear or hub as required.
Drain lubricant to correct level.

Summary of Contents for 2002 X1








































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands