budget BLH 2500, Directions For Use Manual

Page: 12 / 48

12
GB
앬
Make sure that air vents are free of dirt.
앬
Disconnect from the mains after use and check the
machine for damage.
앬
When not using the machine, keep it in a dry place out
of the reach of children.
앬
Use the machine only in the way described in these
operating instructions.
앬
Check that the screws are properly tightened at
regular intervals.
앬
The mains supply must be the same as the voltage
indicated on the data plate.
앬
The electric circuit must be protected at least by a 16A
fuse.
앬
The power cables used are not to be of a lighter duty
class than light rubber-insulated HO7RN-F in
accordance with DIN 57282/VDE 0282 and they
must have a minimum diameter of 1.5 mm
2 . Plug
connections must have earthing contacts and the
coupling must be protected from rainwater. The power
cable must be examined regularly for signs of damage
or ageing. Do not use the machine if the power cable
is in a less than perfect condition.
앬
The efficiency of the machine will be greatly reduced if
a power cable with too small a cross section is used. A
conductor cross section of at least 3x1.5 mm
2
is
required for cables up to 25 m long, and one of at
least 3x2.5 mm
2 for cables longer than 25 m.
앬
If the machine has to be lifted for transporting, be sure
to switch off the motor first and wait for the cutter to
come to a standstill. Each time before you leave the
machine, switch off the motor and pull out the power
plug. Before you connect the machine to the power
supply, make sure that the outlet funnel is properly
connected to the motor housing and the release screw
is tightened.
앬
If the garden refuse shredder vibrates excessively, turn
off the motor, pull out the power plug, and find out
immediately what is causing the vibrations. Strong
vibration is an indication of a fault.
앬
Use only original replacement parts when repairing.
앬
Repairs may only be carried out by a qualified
electrician.
앬
If the power cable for this machine is damaged, it must
be replaced by the manufacturer or its after-sales
service or similarly trained personnel to avoid danger.
앬
Before starting up the machine, and after any collision,
check it for signs of wear or damage and have any
necessary repairs carried out. Always keep your hands
and feet away from the cutting unit, especially when
switching the motor on.
앬
Never use spare parts and accessories not provided or
recommended by the manufacturer.
앬
Unplug the mains plug before checking, cleaning or
doing any work on the machine and when it is not
being used.
앬
Do not wear loose clothing or clothing with hanging
belts or cords.
앬
Do not use the machine on a paved area that has been
gravelled where discharged material may cause
injuries.
앬
Ensure that the loading funnel inlet is empty before you
start the machine.
앬
Keep your head and body away from the infeed
opening.
앬
Do not move your hands, other body parts or clothing
into the infeed chamber, ejector chute or near other
moving parts.
앬
Make sure that you are balanced and standing on a
firm surface at all times. Do not stretch forwards. Never
stand higher than the machine when feeding material
into it.
앬
Keep away from the discharge zone when you start the
machine.
앬
If foreign bodies get into the cutting tool or the
machine generates unusual noises or vibrates in a
strange way, switch off the motor immediately and
allow the machine to come to a standstill. Pull the plug
and carry out the following work:
- Check the machine for signs of damage
- Check that all the parts are secure and tighten them if
necessary.
- Have any damaged parts replaced or repaired, but
use only spare parts of the same type and equivalent
quality
앬
If the machine is blocked switch off the motor and pull
the plug before you start the cleaning procedure.
Ensure that the motor is clear of waste and other
accumulations to protect the motor from suffering
damage or possibly catching fire. In case of motor-
driven machines, bear in mind that the blade also
begins to run when the starting mechanism is
activated.
앬
Ensure that all the covers and guards are in position
and in good working order.
앬
Do not tip the machine whilst the motor is running.
앬
Switch off the machine before you fit or remove the
collection container.
앬
Never try to work with an incomplete machine or a
machine with unapproved modifications.
앬
Connect the electric tool to the mains power supply
(230 V ~, 50 Hz) via a socket-outlet with earth
hing
contact with maximum 16A protection. We
recommend that you fit a residual-current protection
d
device with a maximum nominal tripping current of 30
mA. Seek the advice of your electrician.
BLH 2500_Budget_mehrspr 29.12.2005 10:09 Uhr Seite 12