Budget Robotics TankBot Servo Assembly Instructions Manual Download Page 9 | Manualshive

Page: 9 / 12

background image

Budget Robotics - TankBot Servo

Page 9

Copyright (c) 2002-2006, Budget Robotics

Step 9

Repeat step 8 for the right rail.

Step 10

Using two #6 x 3/4" self-tapping

screws, attach the track rail top

support, as shown.

Do not over-tighten the screws,

or the plastic may become

deformed.

«
...
7
8
9
10
11
...
»

Summary of Contents for TankBot Servo













Reviews:

No comments

Related manuals for TankBot Servo

TI Robotics System Learning Kit

Brand: Texas Instruments Pages: 25

Brand: Loctite Pages: 20

Brand: Same Toy Pages: 56

Brand: Yujin Robot Pages: 47

Brand: EastPoint Pages: 16

Brand: Omron Pages: 16

Ewellix LIFTKIT-OM

Brand: Omron Pages: 26

Brand: Omron Pages: 54

Adept Viper s1300

Brand: Omron Pages: 52

Cobra 350 CR/ESD

Brand: Omron Pages: 138

Brand: Omron Pages: 179

OmniCore V250XT

Brand: ABB Pages: 456

Brand: ABB Pages: 110

Brand: ABB Pages: 266

SWIFTI CRB 1100

Brand: ABB Pages: 22

Brand: ABB Pages: 34

IRB 8700 Series

Brand: ABB Pages: 58

Brand: ABB Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands