Buderus RC35 Operating Instructions Manual Download Page 41

Page: 41 / 60

Logamatic EMS RC35 programming unit - Subject to technical modifications

Operation with the user menu

– Individual heating circuits: only heating circuits which are not assigned to the RC35 will be

displayed; in other words, those which have their own remote control unit or which have no
remote control unit.

4. Setting at home or away from home (absent):

–

absent

: heating is operated at a reduced, adjustable holiday temperature (reduced mode). If

“complete system” was previously selected, DHW and DHW circulation are switched off.
If only some heating circuits are in holiday mode, DHW heating and DHW circulation remain
active (

Tab. 13, page 42).

–

at home

: heating and DHW are available every day as on a normal Saturday.

5. Set the year, month and day, one after the other, for the first day of the holiday period.

Holiday mode starts at 00:00 h (midnight) on the first day.

6. Press

. The year starts flashing.

7. To set the year: hold down

and turn the rotary selector at the same time.

8. Release button. The year is saved.

9. Repeat steps 6 to 8 to set the month and day.

The start date of the holiday period has now been set.

10. Turn rotary selector

clockwise to set the end date of the holiday period.

11. Set the end date of the holiday period by following steps 6 to 9.

12. In addition, for

absent

only: turn rotary selector

clockwise to set the temperature for the

holiday period (factory setting: 17 °C).
The holiday mode is now fully set.

13. Close the flap to finalise your settings.

During the holiday period, the end date is displayed when the flap is open.

If you want to exit the holiday mode early:

Open

user menu\holiday

again.

Answer the question

Do you wish to end the holiday function?

with

yes

To ensure that your home is warm when you return, when

absent,

set as the first day

for standard operation the end date (date of arrival).
When

at home,

set the last day of your holiday as the end date.

During

absent

holiday mode, you can change the temperature simply by turning the

rotary selector. The flap must be closed when you do so.

Summary of Contents for RC35





























































Search results

Summary of Contents for RC35

Reviews:

Related manuals for RC35

Brands by name

Popular brands

Buderus RC35, Operating Instructions Manual

Search results

Summary of Contents for RC35

Reviews:

Related manuals for RC35

Brands by name

Popular brands