background image

7

 

Shutting down the heating system

Logano G234X – 6 720 811 233 (2017/02)

24

7

Shutting down the heating system

7.1

Normal system shutdown

▶ Place the ON/OFF switch in the 

OFF

 position (

 Fig. 29). This shuts 

off power to the boiler and all of its components (e. g. burner, 
temperature controller).

▶ Turn the gas valve ON/OFF knob clockwise to the 

OFF

 position 

(

 Fig. 26, page 21).

Fig. 29   ON/OFF switch in OFF position

7.2

Emergency shutdown procedure

Inform the owner/operator of the procedure to follow in case of 
emergency:
▶ Never put yourself at risk! Your own safety is paramount.
▶ Shut off gas supply!
▶ Shut off the heating system by means of the emergency shutoff 

switch located outside the installation room or the appropriate 
building fuse.

8

Environmental Protection / Disposal

Environmental protection is one of the fundamental company policies of 
the Bosch Group. 
Quality of products, efficiency and environmental protection are equally 
important objectives for us. Environmental protection laws and 
regulations are strictly observed.
To protect the environment, we use the best possible technology and 
materials, taking into account economic points of view.

Packaging method

For the packaging, we participate in the country-specific recycling 
systems, which guarantees optimal recycling. 
All packaging materials used are environmentally-friendly and 
recyclable.

Old appliances

Old appliances contain materials that should be recycled.
The relevant assemblies are easy to separate, and all plastics are 
identified. This allows the various components to be sorted for 
appropriate recycling or disposal.

NOTICE: 

Risk of system damage due to freezing!

The heating system can freeze up in cold weather if it is 
shut down for a longer period.

▶ Protect the heating system against frost when 

temperatures below freezing are expected.

▶ With the controls switched OFF, drain the water from 

the boiler, the DHW tank, the pipes of the heating 
system and, as far as possible, from the DHW piping 
at the lowest point of the system. 

Use the heating system emergency shutoff switch 
located outside the installation room or the heating 
system circuit breaker for emergency shutdown.

6 720 

8

06 02

8

-19.1T

Summary of Contents for G234X/38





































Reviews: